Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Run ducting - high or low ...
-
3rd August 2021, 12:23 PM #1Senior Member
- Join Date
- Mar 2006
- Location
- Newcastle
- Posts
- 120
Run ducting - high or low ...
HI All,
I am a beginner on my Dust extraction Journey. My first post has guided me to the point where I now have a 2HP collector and a plan to house it out the back of my workshop. Here is the post.
I am now finalising the plans for how to run the ducting from outside the workshop to my tools. I am going to try and keep the system with only one (or max two) attachment points in the workshop. All with blast gates.
Ceiling or floor runs?
I would prefer to have the ducting coming down from the ceiling to keep hose out of the way but I believe it will add an extra 5 metres to the length of ducting. It will need to travel from ground level up the wall along the ceiling then back down. If I have the ducting at ground level, it will remove the need to go up and down. In this scenario the total length of ducting from the DC to the tools will be about 3 metres.
Will it make a difference?
From what I have read the extra 5m length will significantly reduce the air movement. Is that right? Or is it a case of a small difference that may not be be relevant when using it for only one tool at a time.
-
3rd August 2021 12:23 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd August 2021, 12:32 PM #2GOLD MEMBER
- Join Date
- Jul 2011
- Location
- In between houses
- Posts
- 1,784
Put it up, the supposed difference in suction will be nothing compared to the frustration of tripping and stepping over the pipework all the time.
-
3rd August 2021, 01:10 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,756
While it would be best to keep the ducting runs at short as possible it will make less difference if its 6" ducting.
If you have the ducting down low does that mean it will cross access ways?
If so I reckon the safety risk of ducting across an access way should not be underestimate
-
3rd August 2021, 02:05 PM #4Senior Member
- Join Date
- Mar 2006
- Location
- Newcastle
- Posts
- 120
Thanks all for your feedback. It has helped.
My current plan is now looking like this.
1. I will route a short 1m run of ducting to near the back door at floor level. I often use the Table saw (on wheels) here so can use that whenever possible. It won't cross the entry to reduce tripping.
2. I will also run a secondary duct - 150mm PVC DWV - up the wall and along the rafters to where I run my mitre saw, track saw, drill press and table saw on occasion.
3. Some lengths of flexible 100mm will be used near the tools and some 35mm to the Mitre saw etc.
What I now need to investigate is:
Can I run both ducts (1&2) from the machine itself. This way I can run the long length on the outside of the workshop. It would mean 1 x 6" (150mm) piece and a 4" (100mm) running off the DC itself. Or is it better to run one length of 6" and put a Y junction in the workshop? I'm investigating this now in the FAQ's - I'm sure the answer is in there!
-
3rd August 2021, 08:18 PM #5SENIOR MEMBER
- Join Date
- Sep 2009
- Location
- Newcastle
- Posts
- 549
I inverted my dust collector which put the intake up near the ceiling and thus saved two elbows and a 2m vertical run
The filters/metal ring diverter/dust bag stay in usual orientation. Motor and impella are up near ceiling rather than down near floor.
-
4th August 2021, 02:25 PM #6
And, if you ever add a cyclone to your system your inlet is going to be up there near the ceiling.
CV1800 | Clearvueoz.com.auStay sharp and stay safe!
Neil
Similar Threads
-
Ducting
By Kevin-R in forum DUST EXTRACTIONReplies: 6Last Post: 13th September 2012, 02:11 AM -
Ducting
By K>60 in forum DUST EXTRACTIONReplies: 11Last Post: 18th September 2007, 09:43 PM -
DC ducting is up and running
By Big Shed in forum DUST EXTRACTIONReplies: 19Last Post: 10th September 2007, 01:24 PM -
Ducting Efficiency
By Grunt in forum DUST EXTRACTIONReplies: 32Last Post: 13th September 2004, 09:00 PM