Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: WC2000 enclosure pics
-
18th December 2009, 07:26 PM #1
WC2000 enclosure pics
Here are some pics of my WC2000 dust enclosure, nothing earth shattering, but it works a treat
Pic 1 shows the right side, note the gap between the bottom and the side, fantastic dust removal. Plan to alter the side so I can attach my planer attachment.
Pic 2 shows the left side with cover removed. The ducting for the saw is manifold ducting, great stuff to work with and doesn't flatten when the saw moves. The fittings are from the 50c bin at bunnies, high pressure water fittings I think. The blue jobby over the inlet on the saw is an ag pipe end cap (bunnies)
Pic 3 is another view of the ducting for the fresh air for the saw
Pic 4 is the underside of the enclosure where the saw gets it's fresh air from. Again, the blue jobby is a 100mm ag pipe nipple, they work great as joiners.
-
18th December 2009 07:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th December 2009, 07:39 PM #2
Here are some pics of my Thien collectors
The first three pics show the triton dust bucket converted. Works very well, attach it to the blade guard on the WC2000 and almost zero dust escapes. The last four are of the big banger attached to the DC7, a 44 with a rubber seal in the lid. Once held liquid fertilizer. Best I can tell, no dust or chips make it into the bags on the DC7. A bit of very fine stuff gets into the bag of the Makita vac, but not very much.
oz
-
18th December 2009, 08:45 PM #3GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Well done ozhunter! Thanks for sharing these with us, there are some interesting ideas there
regards,
Dengy
-
18th December 2009, 11:20 PM #4
Thanks Jill.
Not that any of it hasn't been done before, but I am really pleased with the WC2000 enclosure. The DC7 gets about 99% of the dust and none escapes onto the floor. I could probably get away without the above table extraction, but it's nice not having any dust, compared to before when one cut created a cloud of dust that sometimes caused rain
The collectors are great too. Heaps easier on the machinery.
oz
-
19th December 2009, 12:07 AM #5GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Me again, ozhunter, wiuth a few questions.
Where did you get the manifold ducting? I have never seen it before, that I know of .
How did you make the blue end cap a snug fit over the saw? What model of saw were you using?
How did you make the top of the WC2000 dust proof?regards,
Dengy
-
19th December 2009, 10:34 AM #6
Hello Jill
The manifold ducting came from Auto One.
The blue cap was a perfect fit over the saw without modification, it's held on with a 100mm clamp. The saw is a Triton 235mm.
When I made the panels, I tried to keep the tolerances as close as possible. A piece of weather strip down the long sides fills any gap. The ends were close enough after cutting out the notches for the channel that is on the underside of the table top that I didn't need to add anything. I plugged the gaps inside the top and bottom rails of the bench with pieces of exercise mat foam cut to be a tight fit.
Hope this helps, ask more if I'm not making sense.
oz
Similar Threads
-
Waldo's Dusty Enclosure
By Waldo in forum METALWORK FORUMReplies: 34Last Post: 26th November 2008, 10:49 PM -
Maybe I'm not as pathetic as I thought....enclosure built!
By abitfishy in forum WOODWORK - GENERALReplies: 22Last Post: 4th February 2007, 12:18 AM -
Help needed to construct a projector enclosure
By De_Cruelz in forum WOODWORK - GENERALReplies: 19Last Post: 26th June 2005, 02:12 AM