Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 46 to 60 of 60
Thread: Jack Brabham's Formula 1, BT19.
-
15th April 2013, 10:38 AM #46
Looks great to me Greg. You know we are all our own worst critics. Just having made all the head bolts for the cylinder heads on my engine I understand what you just went through. Love your photography though makes it more interesting at least for me. I do have one question though why the epoxy? I use Titebond II wood glue on everything I make and the wood gives away before it does. It sets in about 20 minutes and hard overnight. Just wondering to each his own. Everytime I have mixed up some Epoxy I feel like I am against the clock and anxious to put stuff together which is not always the best.
Keep the pics coming and make more stuff when you have time. This is no race but the enjoyment of the build and the satisfaction at the end of a job well done.
Bret
-
15th April 2013 10:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
15th April 2013, 11:47 AM #47SENIOR MEMBER
- Join Date
- Feb 2013
- Location
- Bunya Mountains, Australia
- Age
- 69
- Posts
- 522
Ummmmmmm .... I used it exclusively on the liddle boat ... Its fairly harmless to humans, tho some boatbuilders do develop an allergy to it after many years use, but they use it in bucket loads daily.
If you join two pieces of timber edge on at an angle then the bending moment is at the join. You could brass pin it up thru the centre of each piece which distributes the bending moment away from the join. Epoxy does the same .. it just forms a chemical pin once it has set.
But really ... I'm familiar with it, I trust it, and it saves my numerous mistakes from becoming apparent. Also it gives me plenty of 'shed thinking time' while I am waiting for its first set, and I find this time very important .... and you can maneuver it up until that point of first set .. no problems.
Its the same for me with Amoora timber. Its the only timber I have worked with apart from some horrible stuff I started the little boat with. (Silky Oak ... a false and deceiving timber if ever there was one. Soft, does not hold a sharp edge, shines in one direction only to display dull in the other, cells vary in size thru out the grain ... ...I could go on about this stuff ... haahaa)
Greg
-
15th April 2013, 01:11 PM #48
You're doing a good job, Greg, and as Bret says, we are our own worst critics. You see the tiny faults now, because you're concentrating on them, but they won't be noticeable even to you once you're done. This is more detailed than I'm capable of.
I'm enjoying this build, keep up the great work.... Steve
-- Monkey see, monkey do --
-
16th April 2013, 02:54 AM #49
-
18th April 2013, 05:03 PM #50Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Sheesh Greg!! Do you want an electron microscope to get the donk absolutely perfect???
Just incredible!!!
-
18th April 2013, 05:41 PM #51SENIOR MEMBER
- Join Date
- May 2011
- Location
- gippsland
- Posts
- 815
I'm following the build intently Greg, keep up the great work I'm with you on the silky oak one of my least favorite timbers,LOL I had a few nice logs dropped off to mill and cut and split them all into firewood
-
19th April 2013, 07:56 PM #52SENIOR MEMBER
- Join Date
- Feb 2013
- Location
- Bunya Mountains, Australia
- Age
- 69
- Posts
- 522
-
19th April 2013, 07:59 PM #53SENIOR MEMBER
- Join Date
- Feb 2013
- Location
- Bunya Mountains, Australia
- Age
- 69
- Posts
- 522
Haaa ... I know I'm a bit anal about these things. But ... no experience, no knowledge .... So I figure, if each piece is as accurate as possible (allowing for Heisenberg's uncertainty principle) .... then the sum total, the finished piece, will be much better than anything I'm capable of making.
Cool bananas ... Greg
-
27th June 2013, 10:29 PM #54
Greg
What's happening? I hope the BT19 hasn't crashed.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
15th July 2013, 04:36 PM #55SENIOR MEMBER
- Join Date
- Feb 2013
- Location
- Bunya Mountains, Australia
- Age
- 69
- Posts
- 522
Hi Paul (Bushmiller) .... no all is going well, tho at the moment somewhat halted. But soon to start again.
Ta for coming to dinner on the weekend. Was good to meet and debate many points of interest with you and yours. Had a great time.
cool bananas ... greg
-
26th November 2013, 05:37 PM #56
Any more progress yet, Greg??
Any more progress yet, Greg??
Looking forward to seeing the photos.....Cheers, crowie
-
26th November 2013, 08:11 PM #57
-
2nd January 2014, 08:09 AM #58
It's 2014 - Any more progress yet, Greg??
It's 2014 - Any more progress yet, Greg??
Hoping all's well with you for a prosperous new year.
Looking forward to seeing the photos.....Cheers, crowie
-
2nd January 2014, 09:04 AM #59
I did speak with Greg just before Xmas and he is well. He was due to call in here, but a family emergency prevented that. However he did mention that although he had made some small amount of progress on the BT19, it wasn't enough to put up any information in this thread and he was waiting until he had something significant to post.
Regards
Paul.Bushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
9th August 2014, 09:23 PM #60
G'Day Greg, Been too long since we saw your handiwork on the project...
I hope all's well and we soon see your creative workmanship...cheers, crowie
Similar Threads
-
Stave formula
By Chipman in forum WOODTURNING - GENERALReplies: 0Last Post: 10th June 2012, 11:03 AM -
Formula
By kraits in forum METALWORK FORUMReplies: 7Last Post: 27th August 2011, 10:54 PM -
Electric jack suitable for router lift or jack bench
By Woodwould in forum WOODWORK - GENERALReplies: 4Last Post: 25th August 2011, 07:03 PM -
formula for mtrs
By checkerflight in forum WOODWORK - GENERALReplies: 2Last Post: 17th March 2010, 08:53 PM -
The US Formula One **** Up
By Stuart in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 25Last Post: 22nd June 2005, 12:16 AM