Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
26th February 2015, 05:58 PM #1Senior Member
- Join Date
- Nov 2012
- Location
- Belgrave, Victoria, Australia
- Posts
- 234
stabilizing horn? /is there anyone that could help me out?
Hi everyone,
I'm way out of my depth on this one, but i was just wondering if there was anyone on here that was really good with casting/stabilizing oily materials?
I have a small piece of extinct wooly rhinoceros horn that i would like to slice into 'end grain' inlays but at the moment its a bit flaky for my liking.
I was thinking that soaking it in resin under a vacuum system might be able to strengthen it a bit more.
Could someone out there possibly help me out? (i'm happy to pay for it)
IMG_0718.jpgIMG_0721.jpgIMG_0729.jpg
-
26th February 2015 05:58 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
26th February 2015, 08:50 PM #2
I do stabilising with Cactus Juice, and although I am on my way to Melb, I don't have it with me. If you can't get some one to stabilise it your best bet would be to just soak it in Thin CA (not the cheap crap at $2 stores) available at Pop's Shed/Carrols/Carbatec etc (which ever is closer for you).
Dry the horn in an oven at 100C for 15 mins to ensure there is NO moisture. Then use a small container (slightly bigger than horn) and pour CA in, enough to submerge half the piece, for 3mins each end. You can hold it with baking paper when reversing, then after shaking off excess, just leave it on the baking paper for a week to dry completely. DO NOT use accelerator.
That should stabilise the horn. If there are still voids in the horn, you can just start making the pen and fill any voids with the medium CA. Do not use accelerator, just leave to dry overnight, to minimise chances of frosting.
When drilling blank and when turning make sure you are in a well ventilated area with fan blowing any vapours away from you and wear a mask and eye protection. The fumes while doing these are vicious.
Good luck with it.Neil____________________________________________Every day presents an opportunity to learn something new
-
27th February 2015, 07:38 PM #3
Spot on Neil. although I suspect you meant the fumes are ~ vicious (deadly) cheers ~ John
G'day all !Enjoy your stay !!!
-
2nd March 2015, 11:48 AM #4043TURNING
- Join Date
- Jun 2007
- Location
- Adelaide, SA
- Posts
- 478
Cactus juice
Neil,
If you have the pump and chamber - I can send you some juice if that would help .
Mark
-
2nd March 2015, 09:04 PM #5
Thanks Mark, but I am on the road again without equipment, won't be home again until May.
Neil____________________________________________Every day presents an opportunity to learn something new
Similar Threads
-
Another stabilizing system is on the market
By dai sensei in forum CASTING & STABILISATIONReplies: 8Last Post: 10th August 2013, 09:28 PM -
Stabilizing
By Skewpid in forum WOODTURNING - PEN TURNINGReplies: 3Last Post: 28th August 2006, 09:57 AM -
Saw Stabilizing Bracket
By waco in forum TRITON / GMCReplies: 10Last Post: 26th September 2005, 06:44 PM -
Polymerisation or Stabilizing of wood.
By barryr in forum TIMBERReplies: 3Last Post: 2nd July 2005, 07:07 PM -
Burl wood and stabilizing
By Predator in forum WOODWORK - GENERALReplies: 4Last Post: 17th December 2003, 02:48 AM