Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: My Pressure Tank Setup.
-
29th December 2012, 04:18 AM #1Turned a Few
- Join Date
- Jul 2008
- Location
- Red Deer, Alberta Canada
- Age
- 78
- Posts
- 1,958
My Pressure Tank Setup.
I set this up a while back to do my Slab Casting.
Works great for me.
Les
-
29th December 2012 04:18 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th January 2013, 02:55 AM #2Senior Member
- Join Date
- Oct 2004
- Location
- NJ, USA
- Age
- 75
- Posts
- 123
Hi Les,
Have you ever tried to use that pot as a vacuum chamber for stabilizing blanks? We have what is probably the same pot sold by Harbor Freight. I've been thinking about casting and stabilizing blanks for a few months after seeing some really sweet walnut burl pens.___
T.
-
19th January 2013, 03:56 AM #3
A few have tried with limited success Mostly you need to see whats happening while stabilising , as the process can generate a lot of bubbles and the mixtures expand causing problems of overflow and the mixture getting into the vacuum pump , even poly casting will make a mess as the air bubbles through the mixture ,possible solution is a thick clear top with fittings so you can keep an eye on the process and adjust as needed to help solve some of the problems with vacuum. Pressure for casting is a bit different as the levels tend to go down under pressure ,so less problems ,but you need to allow for it and have a well of excess on top of your required or estimated amount for the job and mold , A lot of info on these subjects is in the casting section cheers ~ John
G'day all !Enjoy your stay !!!
-
19th January 2013, 06:24 AM #4Senior Member
- Join Date
- Oct 2004
- Location
- NJ, USA
- Age
- 75
- Posts
- 123
I've watched the videos on TurnTex Woodworks - MesquiteMan's Cactus Juice and seen how much the resin can foam.
I have a bucket full of LEDs and a tiny camera that would be easy enough attach to the underside of the lid and then wire up through the paint suction tube. I'll have to see what I can cobble together before I decide on buying the pot.
I was thinking of something like this:
vacuum_chamber.png
I definitely want to be able to use the pot for both pressure and vacuum.
Of course, a new lathe is of paramount importance ;-) I've my eye on a sweet Nova 2024___
T.
-
19th January 2013, 07:16 AM #5
We just need to talk Neil into being Aussie distributor for cactus juice now that he's not working no more.
OR
Mayne david at timberbits wants to do it for us.
Each of us buying it 1 bottle at a time and paying US postage is going to get costly.
-
19th January 2013, 08:56 AM #6
Good thinking there Trent Maybe a cheap reversing camera with built in leds not sure if that can take the pressure ,should be ok for vacuum though , maybe one of those front door inspection tubes would do the job with the leds It could be a harsh environment inside the pot lol. Cheers ~ John
G'day all !Enjoy your stay !!!
-
20th January 2013, 05:19 AM #7Senior Member
- Join Date
- Oct 2004
- Location
- NJ, USA
- Age
- 75
- Posts
- 123
I spent a fair bit of time googling for other resin sources. I couldn't even find any other retail sources in the state, let alone a bulk dealer.
Shipping and handling is a killer even when it is in-country. I would almost always rather do without than pay shipping charges!
I looked at some of the pricier camera/LED combo's. I don 't think any of them are worth risking even if I could fit them through the paint tube. I think the leads might be shielded, too. With my lashup will just be plain wires that I can solder and seal up in the tube. Buying the pot is the only large expense and it's even bigger than the chamber than TurnTex's largest chamber. And there's no shipping since there's a local Harbor Freight
I really, really dislike shipping charges.___
T.
Similar Threads
-
Could this be used as a pressure pot
By madcraft in forum CASTING & STABILISATIONReplies: 3Last Post: 3rd June 2009, 11:02 PM -
Little Pressure Pot.
By tea lady in forum CASTING & STABILISATIONReplies: 2Last Post: 14th November 2008, 06:00 AM -
Pressure Pot
By Big Shed in forum CASTING & STABILISATIONReplies: 3Last Post: 10th October 2008, 07:11 AM -
the pressure is on
By Christopha in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 29Last Post: 12th October 2004, 04:42 PM