Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Attaching apron with dowels
-
3rd April 2013, 10:29 AM #1
Attaching apron with dowels
I'm in the middle of building a simple bench with a solid core door for the top (plus an 18mm MDF sacrifical layer). The plan I've based it off calls for the apron to be glued to the top's edges with long 25mm x 6mm masonite splines.
Instead of the splines could I use some 6-8mm fluted dowels I have spare spaced at around 100mm intervals along the door instead?
I'm just looking to save a few bucks to spend on other toys instead of having to get a slot cutter for the router which I wouldn't use very often.
-
3rd April 2013 10:29 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd April 2013, 10:48 AM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
Have you got a table saw that you could could use to cut the slots?
-
3rd April 2013, 12:02 PM #3
I'd considered that but not feeling too confident with standing the door up and keeping it vertical to do the short edges. I also just realised that I won't have the roof height to do it unless I wheel the saw outside which would be down a step and a huge pain in the bum.
I guess in a similar vein another option is to put a fence or two on a circular saw. I'd need to make two cuts to get the slot wide enough but could do something with a shim to make that simpler than moving fences.
I was thinking of routing the apron flush to the top of the bench anyway, so I could get away with a little mis-alignment with the slot on the apron side of things.
So the dowels are a no-no? Or is that just an alternative suggestion to doing the splines?
-
3rd April 2013, 01:02 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
What about just adding the apron the other way - with the bench top on top?
-
3rd April 2013, 01:05 PM #5
Doing that many dowels - some 60(?) odd on a std door - you more than likely will have some alignment issues. Unless you're planning on clamping the apron in place on the door, drilling it in situ and tapping in "through" dowels? (In which case you may be better served by screwing the apron on and hiding the heads behind wooden buttons/plugs.)
A spline would still be my preference. Do you have a hand-held CS? Just clamp a straight stud on each side of one edge of the door - to make a wider, more stable face to work on, set a fence and away you go! An edge done in no time...
- Andy Mc
-
3rd April 2013, 01:21 PM #6
BobL: Interesting idea but I'll pass on it. The base has already been cut and half assembled for an 'external' apron and all sized for the door to slip over it. There's a bit of room to play with but I'll lose too much of the overhang I want.
Skew: I think I'll follow up on that idea. Adding width to the door with the studs was the missing piece in feeling confident that I could do it accurately enough with a circy.
Thanks for the brainstorm session fellas
-
11th April 2013, 07:20 PM #7
This is what I ended up using and it worked surprisingly well. I didn't have anything I could clamp to the door for balance, but as long as I kept a little pressure on against the fence and body it didn't tilt.
The job needed two cuts. I was going to tape a steel ruler to the fence for the second cut but couldn't for the life of me find my double sided tape, so I ended up loudly announcing that it was kludge time and put a stack of layers of gaffa tape on instead. Bewdiful
I stuffed up setting the fence for a centered cut even after carefully (read as: inaccurately) measuring everything but it's good enough for me.
Similar Threads
-
apron
By kraits in forum LEATHERWORKReplies: 5Last Post: 25th October 2011, 02:12 AM -
Looking for this woodworking apron.
By highland in forum WOODWORK - GENERALReplies: 11Last Post: 19th December 2009, 10:36 PM -
Leather Apron
By les88 in forum WOODWORK - GENERALReplies: 8Last Post: 27th July 2007, 05:37 PM -
Apron
By Razor in forum WOODWORK - GENERALReplies: 40Last Post: 10th February 2006, 07:50 PM