Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: "good" branch vice screw?
-
11th October 2013, 03:42 PM #1Retired
- Join Date
- May 2012
- Location
- Canberra
- Posts
- 1,820
"good" bench vice screw?
Hello forumites,
I'm building two Roubo benches. Yes, two.
First one is going against the wall and is a "little" one. Its only 1200 long. It won't have the wagon/tail vice.
My question is where to get a good vice screw. I found one on McJing which advertises here and I'm happy to support advertisers (McJING Tools Online at the top) but is this a "good" one?
I can't quantify what I mean by this, but I suppose it could mean smooth thread, sufficient size, meaty threads, longevity, resistance to idiocy, not made of Chinese "metal" etc.
I saw the benchcrafted ones and they are drool worthy, but perhaps later when I'm a billionaire.
-
11th October 2013 03:42 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th October 2013, 04:26 PM #2
Looks exactly like the one I got at carbetec. Not fancy but does the job quite well. They are made in china(like most things) and while the frame shows casting marks the thread is well cut and smooth to turn. I can spin it with one finger.
A pic of how mine turned out.
Regards
John
-
11th October 2013, 04:29 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
The Mcjing vices are the same generic chinese vices as sold elsewhere under other paint jobs, so they won't meet your "no chinese metal" criterion.
Like most things how well and long they work for you depends on type and extent of use. I've had 3 of these cheap vices since 2006 - I got them on special back then for around half the current prices. The one I've used as a front bench vice started out OK but is now so worn and sloppy to the point of needing to be replaced. The smaller side and shoulder bench vices hardly get used so are still OK.
-
11th October 2013, 04:42 PM #4
BobL,
Mine is still new so not showing signs of ware yet. When you say sloppy is it the arm holes or the thread that has worn.
Regards
John
-
11th October 2013, 04:56 PM #5Retired
- Join Date
- May 2012
- Location
- Canberra
- Posts
- 1,820
I should clarify. What I mean by "Chinese metal" is I've encountered a few thing made of "steel" and"iron" that must have been the result of a neighbourhood cleanup. Pots, pans, spoons, tin soldiers and anything that didn't burn off in the furnace.
It was terrible. I had some bandsaw guides that broke in my fingers, screws where the heads twisted off with zero effort and cast iron so full of inclusions it looked like pumice.
If I'm going to buy a vice it's getting daily use. I woodwork for joy, not frustration, so quality counts for me.
-
11th October 2013, 05:42 PM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
The thread is OK, its the holes the arms slide through and hole where the vice screw passes through the front jaw mount that are worn. I've probably not lubed it that often and not used my anti racking stops enough. Also used mine for all sorts of non-woodworking things like holding chainsaws which would not have helped. The wear doesn't effect the holding power but it means the amount of vertical and side racking is much greater than when it was new.
-
11th October 2013, 07:16 PM #7
Cheap not = Quality.
How many times do you want to buy it? (the second time hurts, but the third causes real pain)
-
11th October 2013, 07:29 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
-
11th October 2013, 08:01 PM #9GOLD MEMBER
- Join Date
- Oct 2003
- Location
- Sydney,Australia
- Posts
- 3,157
Have a look at the vises that Lee Valley make, but be aware that you may also pick up a few vices, like Lee Valley/Veritas gadget addiction.
For example:
Veritas® Quick-Release Front Vise - Lee Valley Tools
Veritas® Quick-Release Sliding Tail Vise - Lee Valley Tools
Veritas® Twin-Screw Vise - Lee Valley Tools
Damn, just started drooling again.......
-
11th October 2013, 08:11 PM #10
-
12th October 2013, 12:58 AM #11Retired
- Join Date
- May 2012
- Location
- Canberra
- Posts
- 1,820
-
12th October 2013, 11:02 AM #12
If you want quality and dont have a lot of $ then look for an old Record or Dawn vice. Bit of tlc and they scrub up nice.
Now that I am warned about the ware problem with the chineese one I'll try and keep it lubed to keep things going. I still reckon it will see out my woodworking days.
Regards
John
-
12th October 2013, 11:09 AM #13
Similar Threads
-
"Good" and "Cheap" CMS ? - Yes!
By Grandad-5 in forum HAND TOOLS - POWEREDReplies: 24Last Post: 2nd January 2012, 06:49 PM -
Dawn Vice "Racking"
By Sparhawk in forum THE WORK BENCHReplies: 2Last Post: 7th July 2010, 01:07 PM -
hand plane brass "screw" needed
By Mungo Park in forum HAND TOOLS - UNPOWEREDReplies: 5Last Post: 25th March 2007, 05:23 AM