Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
-
28th December 2022, 03:09 AM #1
Building a MFT: Part Two - making a rail hinge
In the first segment of the MFT build, the aim was to construct a bench top that would accept the Festool accessories for work holding. The MFT would serve for routing, sanding, carving, and as an outfeed for a jointer, slider and router table.
The 20mm holes were routed using a CNC-made template.
It needs to be understood that the reason for making the MFT was partly due the cost of purchasing one in Australia being excessively expensive (the Festool MFT sells for $1595), particularly so when I am not sure how much use it will get.
A large part of this cost lies in the rail hinge and rail fence, since a typical use of a MFT is for sawing ...
The stability and ease of adjustment of Festool rail hinge has come in for some criticism ...
... which has lead to aftermarket versions becoming available, such as this Dashboard hinge ...
This looks a beautiful piece of equipment, camera-level precise ... but it would cost around $700 landed in Oz.
So I decided to build my own. Two considerations - design and materials. The design is a mix of ideas, some taken from other builds on the Internet, Peter Millard's hinge design ..
.. and a few of my own. Fabricating in metal was not feasible as I do not have the tools to work it. Using ply wood, MDF and even hardwood was rejected as these are not durable enough. In the end I settled on nylon cutting boards - cheap and very hard wearing.
The nylon cannot be glued, and so all bolt holes were tapped for threads, and screwed together ...
The dimension across the top is 8" and the height is 5 1/2".
This holder is used for both the hinge side (where the rail is connected) and the pin side (where the rail is squared to the table) ...
Two key factors are present: each part is built with care for precision - errors are additive and will affect accuracy. Part of this is that the hinge must not have any play.
The rail hinge is set at a height below the bench top when not in use.
The two knobs (above right) tighten the connector to the rail ...
The rail connector has rebates to fit the rail ...
The pin in the pin holder is square and sized for a tight slip fit ...
All together - the rail swings over ....
... and rests on the pin ...
The rail is able to be lifted up out of the way in readiness to position a board ..
All feels rock solid.
Checks for square against a rear fence ...
... and against the front of the bench (the ends are exactly parallel and all the holes are square) ...
Lastly, a stop is added to both hinge and pin holders, to allow exact re-positioning ...
All the best for the festive season.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
28th December 2022 03:09 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th January 2023, 10:43 PM #2
Hi Derek
During my research when building my own MFT I found this simple way to autmatically adjust the height of your track by using dual hinges which eliminates the need to adjust knobs.
Tracksaw rail hinge auto adjusting - YouTube
Regards,
Denim
-
7th January 2023, 12:09 AM #3
Hi Denim
I saw that video when I was researching a hinge design. In the end I decided that it was best suited to a permanent set up. Is your permanent and against a wall, as in the video?
In my case, as used today, I wanted to be able to remove the track easily, and turn the table into a work surface.
Do you have a photo of your set up?
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
Similar Threads
-
Wheel Making Part Two Making the Wheels
By htl in forum TOY MAKINGReplies: 4Last Post: 22nd February 2019, 04:35 PM -
Building a picket gate- hinge question
By astrid in forum WOODWORK - GENERALReplies: 9Last Post: 19th November 2014, 10:32 AM -
Building a traditional tail vise - part 1
By IanW in forum THE WORK BENCHReplies: 12Last Post: 14th June 2014, 10:01 AM -
building a vac press for veneering part 1 part 2
By woodman12 in forum CNC MachinesReplies: 6Last Post: 13th January 2014, 11:24 AM -
Is this reasonable for making a cut for a box hinge?
By LGS in forum ROUTING FORUMReplies: 3Last Post: 4th April 2012, 04:23 PM