Needs Pictures: 0
Results 1 to 4 of 4
-
2nd April 2024, 11:25 AM #1
The humble pivoted cross cut stop
When I built my bench (My Xmas Bench), I mainly followed plans by Frank Klausz.
In his plans he had a small pivoted bench stop at the end where the tail vise sits. I wasn't sure about the usefulness. I had enough scraps though, so I just put it on anyway. Just to see if I like it.
And I did. Very quick way to cut off short length from dowels or other pieces. Just flip it up and go for it and then flip it back down again.
Only thing I did not like is that offcuts just fall to the ground. I kept putting a bucket underneath to catch the pieces.
For better solution I build a little swing out tray. I opted for a quarter circle where I could try out round profile with limited thin stock to do the rounded wall.
It folds away nicely
And swings out and ready to catch small off cuts.
I should have made it a bit bigger. Size was dictated by the scrap wood I chose to use. Consider this a prototype until I decide to make a bigger one in 5 years from now [emoji6]
Anyway, I like it and use it a bit. I often have small items I need to cut a short length off.
Sent from my SM-G781B using Tapatalk
-
2nd April 2024 11:25 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
4th April 2024, 10:01 PM #2Senior Member
- Join Date
- Feb 2023
- Location
- Perth
- Posts
- 389
Hi Cklett,
Like your usage of scrap wood and the flip out dust and cut collector is cool.
The flip is next and compact and I see you can use the bench edge to judge square easily, but I have a question. How are you handling splintering that can happen with the last few strokes - flipping or rolling the dowels?
Cheers
-
5th April 2024, 09:50 AM #3
Thanks Martin,
No I am not rolling the dowels or anything like it. The last strokes just need to be very light handed and splintering is very little. You also have to do that or the cut off is being catapulted beyond the tray. The forward motion of the saw gives it a vit of a trajectory..... That's why I should have made a bigger one. But it works and teaches me to be controlled [emoji6]
The pivoted stop is mainly intended where you just want to quickly cut something off. For example for dowels which would be completely hidden it doesn't matter if the end is not fully clean.
If need a perfectly clean cut I would still get one of my mitre boxes out to be honest.
For a quick cut this is a perfect little helper. And costs next to nothing.
Sent from my SM-G781B using Tapatalk
-
6th April 2024, 10:00 PM #4Senior Member
- Join Date
- Feb 2023
- Location
- Perth
- Posts
- 389
Looked at adding one, but at both possible locations, a competing vise is present,. Thought it would be handy. Was intending to add a a small shelf with replaceable strip under the saw- for some additional utility to handle heavier cuts- that could case splitting with self weight.
Will have stick with bench hooks and the no set saw I use. Cross cut most things with this benchhhok set up-except when quite large.
Cheers
Similar Threads
-
For those who have upgraded the Hammer K3 cross cut fence stop ...
By derekcohen in forum TABLE SAWS & COMBINATIONSReplies: 1Last Post: 26th July 2020, 09:44 AM -
N.S.W. Festool Domino 500: DOMINO Cross Stop Attachment
By Bernmc in forum WOODWORK - Tools & MachineryReplies: 3Last Post: 26th December 2019, 11:36 AM -
The Humble Handle
By Bushmiller in forum HAND TOOLS - UNPOWEREDReplies: 7Last Post: 8th June 2016, 08:39 AM -
Cross Slide Threading Stop
By Anorak Bob in forum METALWORK FORUMReplies: 27Last Post: 29th May 2011, 04:56 PM -
Experimental Instrument Prototype (think wiessenborn cross guqin cross I dunno)
By NebulaGuitars in forum MUSICAL INSTRUMENTSReplies: 9Last Post: 14th April 2010, 10:22 PM