Needs Pictures: 0
Results 106 to 120 of 175
-
6th January 2015, 07:13 AM #106
-
6th January 2015 07:13 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
6th January 2015, 08:43 AM #107
Paul
If you are getting "pick up," which is unfortunately very common with many Australian hardwoods, you may have to resort to scraping. With the HNT Gordon planes (and probably other wooden body planes) you can reverse the blade and, in the case of Terry's planes, the planing angle is changed from about 55 degrees to 85 degrees depending on which model you are using.
This works very well but it is harder going so should probably only be used for the final finishing if you can use another method to remove bulk waste. If this becomes an excuse to purchase an HNT Gordon plane, speak to Terry about the best way to go, but probably a HSS blade is adviseable as considerable heat is generated in the scraping action.
The low angle planes do not seem to be suitable for difficult timbers.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
6th January 2015, 09:47 AM #108
For a filler in your epoxy you could use coffee grounds
approach your local coffee shop for some of their waste
I wouldn't use a belt sander and 60 grit to take the 1 mm hump out of the top - you'd end up with a 2mm (or deeper) scratchy dip/lake bed in no time with resultant woes in removing such.
If you're getting this tear out you might need a higher angle plane with a finer mouth and finer cutregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
6th January 2015, 09:53 AM #109GOLD MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Age
- 37
- Posts
- 2,717
How about a router sled?
-
6th January 2015, 10:08 AM #110
-
6th January 2015, 10:10 AM #111
-
6th January 2015, 10:14 AM #112
-
6th January 2015, 12:13 PM #113
-
6th January 2015, 12:15 PM #114
-
6th January 2015, 12:16 PM #115
-
6th January 2015, 12:30 PM #116
Paul and Nick I am using a 62 degree angle of approach provided by the BuJointer that also has the capacity to close the mouth which is the same as the HnT as per DC http://www.inthewoodshop.com/ToolRev...20Jointer.html
Pop wood also suggests a similar approach http://www.popularwoodworking.com/ar...plane_tear-out
which at this point are academic as it is not workin and / or its my limited experience.
-
6th January 2015, 12:42 PM #117
-
6th January 2015, 12:44 PM #118
-
6th January 2015, 12:49 PM #119
-
6th January 2015, 02:25 PM #120
It was only once and may never happen again
Similar Threads
-
Roubo Bench Issues and Questions
By derekcohen in forum THE WORK BENCHReplies: 244Last Post: 31st March 2012, 11:30 PM -
Underhill's Roubo bench
By The Pom in forum THE WORK BENCHReplies: 4Last Post: 14th June 2011, 11:57 AM -
Dan's Blackbutt Roubo Bench
By BozInOz in forum THE WORK BENCHReplies: 215Last Post: 8th April 2011, 08:21 PM -
WIP Roubo bench
By mic-d in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 48Last Post: 30th January 2009, 04:34 PM -
A mans wish
By Gino in forum WOODIES JOKESReplies: 2Last Post: 1st October 2002, 12:21 AM