Results 31 to 45 of 377
Thread: Redefining the Aussie WorkBench
-
1st February 2006, 06:13 PM #31
My bench is a patched together blend of traditional joinery base with a chipboard shelf unit as its top. Two full span drawers and a vice bay-the drawers end up collecting all manner of junk, cannot be accessed when a long board is in the vise.
One good aspect is the very light grey melamine top which repels most of the stuff that I manage to spill on it. Dog holes for Veritas bench hardware, but best of all: they also fit the plastic dogs that come with Workmates-cheap but usable stops that are plane-friendly.
My next bench will have (I think) two solid mdf cabinets with two-way drawers, fitted in a traditional base, and a solid timber top 100mm or so above the drawers. I will have a tail vise, simply because I bought one years ago
The temptation is to have a holding device at every corner, and power points, and an air manifold, and and....
-
1st February 2006 06:13 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
1st February 2006, 06:44 PM #32.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by Rusty
-
1st February 2006, 07:50 PM #33.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
This pic is my Clamp-up bench. I couldn't do with out it. It will Handel comfortably, tops of 2.400 x 1000 right down to small frames and because the spacing blocks were fitted square everything thats clamped tends to come out square even if you don't check it. Best part is when something is glued up you just take it out and lean it up gone a wall and keep clamping. And when not clamping the ply behind sits on top for another utility bench
-
1st February 2006, 08:07 PM #34
Hi Lignum,
When I have some more space, then I'll definately be making a clamp up bench rather like yours - and likely a tool 'butler' as well.
In the meantime I sometimes place a 900 x 600 sheet of 18mm MDF on top of the router table (after dismounting the fence), and use that for lay-up/clamping work. Occasionally the 1800 x 600 deck table gets pressed into service as well :eek:
Cheers!
-
1st February 2006, 08:13 PM #35.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Steve A good idea if your pressed for space, is to make a smaller version (1.8 x .600) and dont put legs onto it. Just lean or hang on the wall and when you need it just lay it straight on your workbench. Its something once you have used it you wonder how you ever went with out it
-
1st February 2006, 08:23 PM #36
Great stuff fellas
I love your 'righthand man Lignum' and really do think gregoryq is onto to something:
"The temptation is to have a holding device at every corner, and power points, and an air manifold, and and...."
and i say why not???........... but lets work out what we really need and what we don't??? Perhaps not holding points at every end BUT 1-2 solid holding points and a 'system' that provides all round worksurface holding capability??
Which brings me to my next question. What tools are we always reaching out for at the Workbench????
For me its:
1. Marking & measuring (LArge/medium/small straightedges/rulers n the like)
2. Chisels
3. Hammers (Heavy/Medium/Light)
3. Drill/Driver
4. Router
5. VArious Fastners
My point being that if we were to go with a base Similar to Markseys then a small storage utility area could be incorporated into the design to allow for storage of the essentials often used at the workBench!!!
.................One of Lignums righthand man's could be used for the rest?????
Regards LouJust Do The Best You Can With What You HAve At The Time
-
2nd February 2006, 12:13 AM #37Originally Posted by Lignum
The tool butler is insane (in the good sense). Mine would also have to include bog, hardener, sanding disks and my drinking water bottle. And lots of pencils, which seem to be "single use only" in my workshop.
I delivered a hall table to a mate tonight who gave me his old temporary front door (insurance job). It's solid core and way big. Hello, new benchtop!
Later,
Rusty.The perfect is the enemy of the good.
-
2nd February 2006, 02:29 AM #38
Gidday
Heres some interesting accessories that I think would be worthwhile intergrating into a modern style of workbench:
Vacuum Clamps
http://www.vac-clamp.com/
Kreg LArge Bench Clamp
http://www.kregtool.com/products/pht...?PRODUCT_ID=68
T-Track
http://www.woodworksupplies.com.au/category4_1.htm
Regards LouJust Do The Best You Can With What You HAve At The Time
-
2nd February 2006, 10:13 AM #39
You can get similar sized hold down clamps (like half a pair of vise grips)
for drill presses. eBay price was 19.00 shipped for my last one. They have a 12mm stud, so 12mm nut plates would have to be installed.
I have that vacuum clamp-it works so well that I have a similar fence for my slider on the to-do list. My only complaint is the constant hiss from the air needed to blow the venturi.
You also mentioned the pattern maker's vise. The originals were Emmert and are prized things. I read a review of the Chinese clone that said they made nice boat anchors.
I am making a set of air clamps for my machines, I'll do a post on the process. I am 6 weeks or so away from getting to it. I plan on being able to use them as hold-downs on my bench.
Greg
-
2nd February 2006, 10:36 AM #40.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by gregoryq
-
2nd February 2006, 10:50 AM #41
Hi Lignum...
There is a guru on the Felder Owner's Group who made the originals, and they are commercially available, but way too exxy at $800.00/pr. I am making mine from eBay parts for approx $40.00 each.
The other thing I want to make is a vacuum rip fence for the slider for thin pieces of stock. Since the stock gets fixed to the fence, this is possible. I am using an incra fence attached to my outrigger for this now.
Here's a pic:
-
2nd February 2006, 11:04 AM #42.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by gregoryq
Vacuum power is one of the great workshop tools thats sadly over looked my the majority as they think its to hard/expensive. A household vaccuum, a piece of MDF and a round rebate with rubber door sealer will cost three or four dollars and twenty minutes of mucking around and even the weekend hobbiest can have a basic hold down
-
2nd February 2006, 11:16 AM #43
The funny thing is that they are the same parts, just supplying my own late evening labour. Making jigs and workshop aids is one of my favourite things, so it's not even like work.
I have a few PDF files from the Felder group that show member made devices-please send me a pm with your email address if you'd like copies.
Greg
-
3rd February 2006, 05:22 PM #44
Base Design ......Contributors welcome
Gidday
Well my CAD skills arn't fantastic but I'm getting to the stage where I can slap together a reasonable concept drawing.
Heres my initial concept drawing for a Base (Pic1). Perhaps we can get to joinery after an initial design concept is established. I think I can dimension it up once we finalise a design.
Well I've been on a roll and added a base with tusk tenions(Pic2) and through wedged Tenons (Pic3)
Does antone think a rail is needed Uptop?
.............All design suggestions dimensioning ideas really appreciated.
Regards LouJust Do The Best You Can With What You HAve At The Time
-
3rd February 2006, 08:34 PM #45
Here's my 2c worth Lou, not a new idea, been brought up before, but anyhow...
My first benchs are "mostly" built. Got 1 finished and had to move, so its twin is in pieces waiting my next visit home for assembly.
25mm square box section steel and 30mm box section steel. I used a wall thickness in 30mm so that the inner dimensions are about 0.6mm larger than the 25mm outer dimensions.
Top 'stretcher' is 30mm box, welded to legs, legs 30mm. 25mm pieces form "elbows" so rails slip over them. Basically 3 leg assemblys, ends and middle of bench top. 4 rails in total, 2 each side front and back (between each leg assembly), bolted on for security.
Benchtop is 2 sheets of 25mm thick 6 foot x 3 foot MDF sheets. I got a heap as "seconds" (they were overweight for spec) at $9 each. Sheets are glued together (one on top of the other) and faced with tempered masonite, bottom side painted to seal it. Edge banded with "Tassie oak". Top joined to rails via self drilling screw (recessed into MDF and bogged over).
Its a POS from the traditional perspective, but:
its cheap, the top is heavy and absorbs hits when bashing stuff (which I try to stay away from doing), masonite is sacrificial and replaceable. I can put clamps off the steel rails, its big, its flat, its stable. Did I mention it is cheap?
Couldn't be fussed with rails and dogs, I'll just screw down battens as needed.
The plan is to have one as a work bench, and one as a glue up table (this one on castors). If you think about adding shelves and drawers its just a matter of another leg frame or box section uprights.
I was all set for a traditional benchtop, but I'll leave that for when I have spare cash. This lets me get on with the job and I'll put the money I save on the home loan.
They will be able to be broken down if/when I move house, so that was a consideration. I try to think "modular", same for shed power and stuff like lighting.
If it racks I'll weld in a cross brace, if it moves I'll bolt it to the slab or something. The vise is on the go, basically waiting for me to weld in a mount frame.
Thats my (bloody ugly) Alternative Workbench.
Bloody Ugly, but she is practical and works. Fancy is for later, and affordable is for now.
Similar Threads
-
The Perfect Workbench?
By DarrylF in forum THE WORK BENCHReplies: 85Last Post: 14th August 2007, 11:33 PM -
The Aussie Way
By doublejay in forum WOODIES JOKESReplies: 1Last Post: 19th April 2005, 10:02 PM -
First project - workbench
By javali in forum THE WORK BENCHReplies: 18Last Post: 19th January 2005, 12:20 PM -
Catch-22 - building a workbench without a workbench
By brianhay in forum THE WORK BENCHReplies: 11Last Post: 18th January 2005, 04:56 PM -
The Englishman, the Frenchman and the Aussie
By Driver in forum WOODIES JOKESReplies: 0Last Post: 9th June 2003, 08:25 PM