Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 58
Thread: WIP - Really basic
-
13th May 2013, 11:06 PM #1
WIP - Really basic
Well there have been a few people who have doubted whether I would ever start this thread, and I was one of them, but this is the beginning. The concept (and it really is a concept) is for a split roubo style bench with three vices. A leg vice, a sliding tail vice (HNT Gordon) and a MCW (Michael Connor woodworking) woodworking style vice in aluminium to adorn the bench top.
Timber is spotted gum for the top and a red timber for the undercarriage: Probably will be forest redgum as I have some of that lying around in suitable sizes.
Here is the spotty still standing:
lathe 011.jpg
Spotty down and me still standing. Best that way .
lathe 015.jpg
Docked into lengths
lathe 018.jpg
Some timber appearing on the trailer:
lathe 042.jpg
Back at Millmerran:
lathe 049.jpg
There is some timber for other purposes too such as glass doors and a couple of framed, ledged and braced doors. Also there is a tapered blank for a didgeridoo for Simon you can see on the offside of the vehicle. In fact the timber only represents half of what I milled and there are still a couple of log lengths to saw. My ute was not up to carrying the lot. It amounted to about 850Kg of green spotty plus other gear I was carrying. Quite heavy enough for a 600Km trip.Quite a good yield from a single tree especially as I was primarily trying to obtain quartersawn boards.
Later this week I will stack out the timber for air drying and later again I will be putting an improvised solar kiln over the stack for final drying. I aim to get down to 30% moisture content by air drying which may take up to six months with 50mm thick boards as we are coming into winter.
I will be putting more detailed information on another thread in the timber milling section and will post a link for those of you who are interested in the mechanics of quartersawing.
Incidentally, I opted for quartersawing as it produces more stable timber, but that is probably the only benefit of quartersawing. It is more difficult to cut (particularly with a bandsaw), less attractive (not an issue here), not as strong (definitely not an issue) and the yield is slightly less from the log compared to backsawn. Otherwise all good .
Oh, there is another downside. Timber tends to bend up towards the bark as it is cut. This happens equally whether timber is quartersawn or backsawn, but with backsawn you stand a chance of flattening the board during drying. The quartersawn board bows on edge. No chance of straightening that in a 125mm board. Jointing is the only option either mechanically or by hand.
Needless to say, more information to come.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
13th May 2013 11:06 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th May 2013, 03:54 PM #2GOLD MEMBER
- Join Date
- Jan 2010
- Location
- Melbourne
- Posts
- 2,636
Subscribed
-Scott
-
14th May 2013, 04:08 PM #3
-
14th May 2013, 05:01 PM #4
-
14th May 2013, 07:52 PM #5
Paul, it's worth noting that with the new forum format there is no "old Thread" button to click, so you'll have to make at least one entry every three months to keep the thread alive.
-
14th May 2013, 08:02 PM #6
-
14th May 2013, 10:11 PM #7
Interesting one to watch.
-
14th May 2013, 10:35 PM #8
Also subscribed
The poor old ute gets another serious workout.Those were the droids I was looking for.
https://autoblastgates.com.au
-
14th May 2013, 10:46 PM #9
-
15th May 2013, 12:06 AM #10SENIOR MEMBER
- Join Date
- May 2009
- Location
- Coffs Coast
- Posts
- 141
WIP - Really basic
Bushmiller,
I'll be watching with interest. I've just begun my all Aussie Bench Build.
Northern NSW recycled hardwood joists with house stump legs from Woolgoolga, to be adorned with MCW face vice and HNT Gordon tail vice. Busy in the shed dressing down some lovely old growth euc ( flooded gum perhaps) legs by hand. I think it'll be about 0.2m3 of timber when done. ( 2.6m by 0.6m or so for the top). As I'm dressing by hand and your milling from scratch I think I might be done round the same time as you...
-
15th May 2013, 02:02 PM #11
-
15th May 2013, 02:06 PM #12
For those of you that are interested, this is a link to the more detailed milling side. Still a bit to go there too as I didn't get to the quartersawing side of things as I was thrown off the computer . I knew it was a mistake marrying a weightlifter .
https://www.woodworkforums.com/f132/b...ed-gum-170760/
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
15th May 2013, 02:25 PM #13
Apologies for this comment, Paul...
BUT if it's going to take at least 6mths for the freshly saw timber to dry before any bench building action is going to really happen; isn't it like watching paint dry in the mean time...
Watching a stack/pile of timber air drying may even be a worse deal.....
Cheers, crowie
-
15th May 2013, 02:33 PM #14
Peter
I just knew I was going to have to endure this type of comment. You didn't sit too close to Brett at the GTG2 did you. I thought you seemed a really good bloke, but obviously some of Brett's DNA has rubbed off .
It will be a while, but that is no matter as during the drying time I will be building the new shed to house the bench!
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
15th May 2013, 02:41 PM #15
As I started the post - APOLOGIES Paul....
It was too much of a temptation and while I only live 30mins from Brett I was loath to pay out on a fellow Queenslander...
I will enjoy watching the bench come together even if slowly, like many of my projects.
cheers, crowie
Similar Threads
-
Basic toy car
By michael_m in forum TOY MAKINGReplies: 10Last Post: 2nd July 2011, 10:11 AM -
Another basic question
By celeste in forum WOODWORK - GENERALReplies: 5Last Post: 23rd March 2007, 11:20 PM -
Basic box strength
By CarpeNoctem in forum WOODWORK - GENERALReplies: 8Last Post: 21st October 2005, 07:55 AM -
cradle , basic
By rick_rine in forum WOODWORK PICSReplies: 6Last Post: 21st September 2005, 09:18 PM