Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Brick in post hole
-
27th October 2011, 07:19 AM #1
Brick in post hole
I have been trying to work out why the instructions for a Stratco shed want a brick placed in the post hole.
The instructions say to dig out all your holes and then place concrete in the bottoms with the tops of the concrete to the same level, about 400 mm from the surface. Then, before you stand your wall up, place a brick on top of the concrete to which the up right of the shed is placed.
I cant think for the life of me why? The level has already been determined by the initial concrete pour. It does nothing to bind the upright to the concrete and if you wanted the uprights higher you could just make the initial concrete pour higher. As for saving on the volume of concrete, it would be so small, if any and probably more of a pain if you don't have spare bricks lying around.
Any ideas ? The kids at Stratco just shrug their shoulders when you ask them anything.Try to look unimportant, they may be low on ammo.
-
27th October 2011 07:19 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
27th October 2011, 08:09 AM #2
The only reason I can think of is to assist in getting the final column height level. Have not ever come across before, there are simpler ways of determining the final level.
Maybe some new fangled idea by a structural engineer that is so new even Stratco don't know about it?
-
27th October 2011, 10:34 AM #3SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Nrb
I think you will find that the reason you sit the steel post on as brick is to stop it settling through the concrete as it sets
-
27th October 2011, 01:12 PM #4
I could understand if the brick were placed in the hole before concreting so that the post is not in contact with the ground, but to have a brick suspended in the footing...??
When I built my own sheds, I had a piece of timber stud screwed to the post just above ground level which straddled the hole. I could then raise/lower each post with timber packers or pavers or whatever to adjust my heights before pouring the footings.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
27th October 2011, 03:26 PM #5
I agree with NRB, the brick is to stop the upright from sinking into the cement mix and give it a solid base,
Jeff
-
27th October 2011, 05:32 PM #6
-
27th October 2011, 06:02 PM #7
Instructions are never logical, especially if the machine is of ORIENTAL ORIGIN.
The shed is not I take-it?? could be a miss print, .
I normally put a brick or small besser block in the bottom , then the post , followed by the post-mix.
-
27th October 2011, 06:09 PM #8
I think that NRB may have the answer. I am doing the holes and the concrete a few weeks before the shed even arrives, so it didn't even dawn on me that some people may be doing the holes just prior to standing the shed up and the concrete may not have cured enough to prevent the post from sinking into the fresh mix.
Try to look unimportant, they may be low on ammo.
-
27th October 2011, 06:17 PM #9
My guess - to provide a drainage space so water does not build up around the post and cause accelerated corrosion.
-
28th October 2011, 07:16 AM #10Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Ring Stratco and ask!!
-
28th October 2011, 10:37 AM #11Member
- Join Date
- Jan 2011
- Location
- Ft. Myers, Fl
- Posts
- 84
Brick in a hole
G'day Y'all
Here in Florida we have learned that wood and concrete do not go well together. Moisture accumulates on top of the concrete and rots the wood very quickly. The brick is porous and will wick moisture away from the wood. It is a good idea to soak the wood with waterproofing also.
Regards
Joe<style type="text/css"> <!-- @page { margin: 0.79in } P { margin-bottom: 0.08in } --> </style> Politicians are like diapers.
They need to be changed for the same reasons.
-
28th October 2011, 08:44 PM #12GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
I think its a steel shed. The only reason I can think of would be to stop the open end of the RHS sinking into the concrete. That is, if the end is open. It would also make a smooth surface to move the post on to locate its correct position.
-
28th October 2011, 10:34 PM #13
Similar Threads
-
Talon post hole digger
By losh1971 in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 1Last Post: 13th October 2009, 06:31 PM -
Post Hole Boring
By STAR in forum MY RURAL BLOCKReplies: 11Last Post: 1st September 2008, 02:03 AM -
Drilling large hole over small hole or vice-versa
By niki in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 28Last Post: 2nd November 2007, 08:32 PM