Needs Pictures: 0
Results 1 to 15 of 72
Thread: shed lining
-
16th May 2013, 11:57 PM #1
shed lining
I am thinking of lining my workshop in 19 mm partical board or 12mm plywood with it off the floor with a 19mm X 42mm foot of treated pine to stop the ants & rot
with insulation behind it, Then covered in plaster board to give it a nice finish, has any one done this. I want to have a bit of a sound deadining withit so I can have it nice
Regards Michaelenjoy life we are only here a short time not a long time
-
16th May 2013 11:57 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
17th May 2013, 12:08 AM #2
Michael, first of all I wish I had your type of shed reno budget. Two layers of plaster (ideally 13mm) will work better and should cost less. If really concerned, use two layers of Fyrecheck...actually has a better rating than Acousticheck.
Other than that, i'm sure your going to get a flood of responses from the sound gurus.
Craig.
-
17th May 2013, 12:09 AM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
I'd save yourself a hell of a lot of work and just go with insulation and either the wooden or plasterboard lining.
Are you putting the wooden backing for attaching things to?
If so then you can just put plywood over the plaster just in areas where it is needed - this also protects the plaster underneath - like this.
-
17th May 2013, 02:09 PM #4Senior Member
- Join Date
- Oct 2007
- Location
- Tasmania
- Posts
- 132
I lined my shed with16mm chipboard, a 1200x2400 cost me $13.20 a sheet, which was "seconds" direct from board manufacturer. I have found this great as it doesn't get dinged when I swing things around and I can screw whatever I want and wherever. I also put colourbond On the ceiling, because it was cheaper than plaster, didn't have to paint it. Also to my understanding the ripples of the corrugates help the deflection of sound.(you can get a perforated version designed to be used with a sound blanket. I've seen this in school gyms)
-
17th May 2013, 02:15 PM #5
I've lined my shed with 16mm White Melamine. Heavy sheets. The white allows me to use my shed without supplementary lighting more often.
Pat
Work is a necessary evil to be avoided. Mark Twain
-
18th May 2013, 07:27 PM #6
I am putting in more steel perlins to support the wall linings. The budget is I get what I can afford as we get paid monthly so I will be doing one wall at the time. As I have lost the ability to work on cars I am putting all my energy into my woodworking & workshop hence the lining of the work shop. I have just been informed this is all mute for the next 2 months as I am having back surgery on the 4 th of june & the second op on the 18 th then its 4 to 6 weeks of no heavy lifting from that time. For the roof I have already got 40 mm poly styrene panels up there already with silver bats on the shed side between the perlin's but I will look at using the colour bond on the inside save putting up lining boards there as I was not looking forward to doing that I will scrounge the demo yards for the extras
Thanks for the reply's
regards Michaelenjoy life we are only here a short time not a long time
-
18th May 2013, 09:32 PM #7GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 2,750
-
18th May 2013, 10:20 PM #8
Good luck with the ops.
Craig.
-
18th May 2013, 10:32 PM #9
not worried about the ops. it is the shed the shed that worries me
if they stuff up the ops i will have to rebuid my work benches & lathe stand lower so I can sit & wood work
regards michaelenjoy life we are only here a short time not a long time
-
18th May 2013, 10:59 PM #10GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,695
Line it with a heavy board all round and use a cleat system to hang things, this allows changes as needed and is very versatile.
Workshop wall hanging system - try French cleats. / Latest articles and discussion. - FESTOOL Shop and User Knowledge BaseCHRIS
-
20th May 2013, 02:20 AM #11
I have only done one wall of my shed, & I did it to hang stuff on.
My shed is a standard tin shed with C section posts & rails.
I made timber frames & screwed then the the rails between the posts. When I did this, I ran 2 Horizontal & parralel beams between each timber upright, about 150mm apart (internal)
I boared a couple 25mm holes through the timber uprights, inside these horizontal beams.
Then I glued & nailed a strip of 18mm MDF to the back of the Horizontal beams.
I screwed the timber frames to the Shed wall and cut a sheet of MDF to fit from the bottom of the frame to about the mid point of the bottom horizontal beam.
I cut a narrow strip of MDF to go from the the top of the last sheet to the mid point of the top horizontal beam, & then the last sheet went from there to the roof of the shed.
By screwing the top & bottom sheets to the timber frame, I now have a sealed conduit to run electrical cables, with a removeable strip on the front.
I made a similar section on the end to run cables up the post for lights & power over the apex of the roof.
It's not a great pic, but you can see the conduit cover above the belt sander.
shed2.jpg
SteveThe fact remains, that 97% of all statistics are made up, yet 87% of the population think they are real.
-
2nd May 2015, 08:31 PM #12
I know this is an old post of mine but due to health things in the shed had stopped happening
I was looking on the net and had a bonus find
20150502_123314-1.jpg
I managed to get 20 sheets of s/h 17mm X 1200 X 2400 plywood for $20 per sheet off gumtree here in adelaide
and have started putting it up
regards Michaelenjoy life we are only here a short time not a long time
-
2nd May 2015, 10:02 PM #13GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
Nice work Michael, how did the back op go, all well I hope.
Regards
Kryn
-
3rd May 2015, 04:15 PM #14
1st operation was half successful still have pain and getting bad again. O well that's life wont let then do the second one. Due to it being on the S1 and S2 bones in the coxic and the the pain related with it. Constant pain is with me all the time. But it sucks having to work slow now in the shed. Got 3 panels up in the shed only 15 more to put up then in goes the gas heater to keep the cold out while trying to work.
Regards Michaelenjoy life we are only here a short time not a long time
-
3rd May 2015, 06:22 PM #15GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
Hi Michael, I know what you mean about constant pain, it certainly is the pits. It gets to the stage quacks look at you and think you're a hypochondriac. Problem is that there is nothing legal, to help with it.
Why not invite a few mates around to help with the wall, put on a barby, 1 Sanger each though . I'm sure some from here would come and help, if it gets to hard for you..
Regards
Kryn
Similar Threads
-
The shed gets a lining
By rusel in forum THE SHEDReplies: 49Last Post: 29th June 2013, 09:03 PM -
Another shed lining
By snowyskiesau in forum THE SHEDReplies: 0Last Post: 30th December 2012, 08:43 PM -
Shed wall lining and insulation
By Onezero in forum THE SHEDReplies: 5Last Post: 18th May 2012, 11:52 AM -
Lining for storage shed
By mondo45 in forum WOODWORK - GENERALReplies: 4Last Post: 2nd April 2012, 03:24 PM -
shed lining
By coffenup in forum THE SHEDReplies: 12Last Post: 11th December 2011, 08:11 PM