Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 6 of 6
  1. #1
    Join Date
    Apr 2011
    Location
    McBride BC Canada
    Posts
    3,543

    Default How Soft Is Your Paper?

    I used dry paper for my very first (and so far, only) wood cut printing. The prints were a bit blotchy and this was not the same from one print to the next. Not enough ink, methinks = gooey little blobs of ink here and there. That was not the solution.

    Later, I learned that the paper needs to be softened with water and rested in a pile. Not so much to aid the transfer of a water-based ink but moreso just to make the paper softer and more flexible, even with oil based inks.

    Irrespective of paper weight and texture, is there a way to judge this factor before printing. . . even if the proofing sheets are another grade of paper?

    I've got to get some projects completed in the next 2 weeks for Rivers Day, Sept 24.
    Can't allow myself to work on this until after that event, for certain.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Apr 2007
    Location
    Melbourne
    Age
    56
    Posts
    235

    Default

    Depending on the type of paper/ink/press/inking technique you are using, one way to try is get your editioning paper ready and dip the first like wallpaper through a trough/tray of cool water then let it drip off a bit and lay it on a sheet or two of CLEAN newsprint, pat it down a bit then Do the next one and continue layering on newsprint when you've finished flip the stack over onto a sheet of plastic big enough to wrap the pile up in, leave it for an hour or so while you pull some proofs,modify ink, drink red wine, then they are ready for printing. the idea is that the time and layering allows the moisture to even out in all of the sheets. prep more sheets than you intend so you can pull a proof or four ie. two for press pressure, two for ink modification.
    Hope this helps, I'm more of a painter these days but still remember a trick or two.

    Ian

  4. #3
    Join Date
    Apr 2011
    Location
    McBride BC Canada
    Posts
    3,543

    Default

    I quit carving/art in April and spent as much time outdoors as possible over our summer. WX now just as cold, windy and rainy as a winter in Melbourne. . . . and it will get a whole lot worse before it gets better. Freezing level is less than 5,000', down into the trees/forest. I'm just about ready to retreat into my house & shop.

    The paper: I've painted in watercolor for 25+ yrs. The printing paper needs to be about as wet as WC paper for stretching? Another opinion claimed just damp for pliability's sake. Spray the sheets, stack & wrap, wait a couple of hours. Do you think that I should try both to figure it out?

    Process: wood blocks, water-base inks & brayer. Paper and my hands/spoon for a press. I have every intention of building a press. Of course I do. One of these days.

  5. #4
    Join Date
    Jul 2008
    Location
    Yarra Junction Vic
    Posts
    280

    Default

    Don't know how much further you've got, but when I get my students to print intaglio (etchings and engravings) we wet one side of the paper and leave it for 1 or 2 min. We use just cartridge as its cheap and as long as the (oil based) ink is fresh and the press pressure is up it works a treat. For lino I use an old office press, which applies screw down pressure (relief plates can slide out from under the rollers and smudge). Should be easy to use a couple of flat pieces of timber and some big G clamps to squeeze it.

  6. #5
    Join Date
    Apr 2011
    Location
    McBride BC Canada
    Posts
    3,543

    Default

    Thanks IGGY. I've just finished 2 wood cuts, ready for printing. However, I have guests coming and going and 2 more birthday toots to get past, then Christmas with family flying in. . . . I won't get to the blocks until January.

    I don't have a press of any kind. Figured I'd start with some sort of burin or hand pressure and see how that goes. I did the Ookpik prints on dry paper (not knowing any better) and they were quite blotchy (water-based ink.)

  7. #6
    Join Date
    Jun 2009
    Location
    SE Queensland
    Posts
    163

    Default

    Just came across this rather ancient thread.......Re making a press....some time ago I came across an article about using a car jack to make a press. There's quite a bit out there as you've probably already found. Here's one link:

    https://www.printcouncil.org.au/unca...press-at-home/

Similar Threads

  1. Soft Edge 2D
    By cultana in forum DESIGN & DESIGNING / GOOGLE SKETCHUP
    Replies: 0
    Last Post: 25th September 2009, 01:29 AM
  2. Air Con: Soft Start?
    By memphis in forum HEATING & COOLING
    Replies: 4
    Last Post: 3rd May 2008, 01:14 AM
  3. Soft Maple?
    By yvonne in forum SCROLLERS FORUM
    Replies: 3
    Last Post: 5th February 2008, 08:55 AM
  4. Soft down stays
    By Jemoge in forum HAND TOOLS - POWERED
    Replies: 7
    Last Post: 31st May 2005, 09:50 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •