Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Foundry Myths
-
26th October 2012, 02:27 PM #1
Foundry Myths
Hi All,
I found this video very informative...
Foundry myths - YouTube
Not that I'd be all that keen to repeat the experiments...
There are a number of good videos by the same guy
luckygen1001's channel - YouTube
Regards
Ray
PS. I think he's somewhere down Gippsland way.
-
26th October 2012 02:27 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
26th October 2012, 03:49 PM #2Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Would like to have seen the experiments done with cast iron rather then aluminium....
Light red, the colour of choice for the discerning man.
-
26th October 2012, 07:14 PM #3Senior Member
- Join Date
- Jun 2012
- Location
- Germany, Outback of Munich
- Posts
- 213
I know this video.
But as soon as the water gets below the molten metal's surface, the fun is over.
I spilled half a crucible of aluminium in 0.1 seconds that way.
Nick
-
26th October 2012, 07:41 PM #4
Foundry explosions
When I was an apprentice back in the 60s there was an explosion at Ultimo Tech when the Patternmakers where doing some casting. The sand was too wet and as a result the apprentice 2 years my senior copped metal in his leg.
I recently did the night TAFE foundry course at the 'gong where after showing you how to, it was open slather on doing your own projects.I had just made the pattern for a plaque for a navy LST and thought I would prove it using scrap brass plumbing taps etc for the melt. There was no way they would put my scrap in the pot because of the risk of water in the tap chambers.
So whilst good entertainment the video is very dangerous for all the amateurs out there.
The TAFE had been set up by BHP but they never put anyone thru it.
It survived for a while on car restorers and steam nuts and sculptures etc.
They had a great furnace it would melt cast iron in 20 minutes but you could only pour what 2 people could lift. Much better than the old cupola we used at the Ballina slip where we used wine flagons for flux.
H.
-
27th October 2012, 06:24 AM #5SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
-
27th October 2012, 10:16 AM #6
Sorry about that. I am obviously not at all nuts.
Just in from the shed where I'm restoring a 3 wheel Mazda ute.
Also a timber framed convertable (Morgan).
Ive even kept 20ft of line shafting in the roof.
Have a Buzacott to hook up to it 'one day' but would love a small steam engine.
H.
-
7th March 2013, 10:52 PM #7
Hi .RC.
Still not sure I'd be game enough to try, but here's the cast iron version Foundry myths revisited - YouTube
Regards
Ray
-
7th March 2013, 11:14 PM #8
Big girls in runners
How would these turkeys go if the plug didn't stop the pour from the cupola and they had to run through an inch of molten iron on the foundry floor to try and stop it all from covering the entire foundry.
Ballina Slipway and Engineering 1975.
We had a 'few beers' at the "Pot" after that one
SG was also using the black zircon sand for blasting in the boiler shop
To say nothing of the welding leads the fork used to run over.
Maybe the Chinese or Indians will see this and think it's a safety film.
H.
Similar Threads
-
urban myths
By underfoot in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 0Last Post: 28th December 2010, 05:49 PM -
Australian Myths
By Barry_White in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 6Last Post: 20th May 2008, 12:50 PM -
MDF myths,
By Gaza in forum WOODWORK - GENERALReplies: 18Last Post: 8th July 2005, 08:54 AM -
Grounding PVC and Other Dust Collection Myths
By Wayne Davy in forum DUST EXTRACTIONReplies: 2Last Post: 14th May 2003, 04:19 PM