Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 33 of 33
Thread: Melting aluminium
-
11th August 2009, 09:50 PM #31
Kero makes a good coolant for ally of most grades .Ive machined ally sheet with my woodwork router and some cheap Bunnies carbide bits .I usually mark it out first and then use a paint brush and paint a bit of kero along the cut line.
Candle wax works too or even the lard from the Sunday roast( smells better ) .
We have some big sheets of 50mm 6061 at work for machining aircraft parts from .
Lucky for me I get the off cuts that are too small for anything they want to make.
Machines nice with tungsten carbide tipped tools on the mill.
I would look at getting a sheet or a cut sheet of 16mm or 20mm ally plate maybe 6061 for the table top .
Or Go to a foundry and ask if you can scavenge though thier scrap pile look for a cast iron machine table.
I use to work for a company that had a cast iron foundry , there was all sorts of good stuff in the scrap pile.
Kev."Outside of a dog a book is man's best friend ,inside a dog it's too dark to read"
Groucho Marx
-
11th August 2009 09:50 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th August 2009, 11:54 PM #324-6-4
- Join Date
- Mar 2009
- Location
- Melbourne
- Posts
- 295
Aluminium Melting
I can't resist this thread. I had a small non ferousios foundry that was geared to The Model Engineering game. Speaking as one that knows any molten metal and water do not mix. I had two explosions with ally once when there was water in the ingot mould and I was pouring the remnants of a melt into the mould. this was only a small amount of metal but gee it was spectacular I still have a mottly cap from this adventure. The secon time I was melting scrap (not cans) to make Number Plates. No need for quality. The last pieces ito the 15 Kilo crucible were some radiator fittings. I pushed them down and there must a been the tinest amount of water only dampness and the result was even more spectaculat.
The only problem I found with melting from Ingots was the size of the beasts. I bought ingots that you broke in half with a sledge hammer and these went into the 15 kilo crucible. This was of a maximum size I could handle by myself. Even when I used ingots I used a cleaning agent to bring a the gunk to the surface of the melt. These tablets were pushed to the bottom of the melt and bubbled away furisly. Most were pretty toxit not recomended for enclosed spaces. But they did work. Ally cans have an ally in them to make the metal extrude around a former so are not very good for quality work.
Finally a word on furnaces for those fool hardy adventures. The stuff to use for the lining of the furnace is Kaowoll. I am not sure if this is the correct spelling but it is the way it is spoken. This stuff reflects the heat and thus reduces the melt time. it comes in a blanket up to an inch thick. Wraped around a drum 1 layer is enough. You have to be gentle with it when removing a crucible but with a normaly asperated blow torch you are in busines. My furnce looked terrible but it did the job.
If any one is interested I will talk about moulding sand and other foundry bits later on.
Yoursn 4-6-4
-
15th August 2009, 12:17 AM #33
yep Kaowool, it is used a far bit at the smelter
Similar Threads
-
melting wax
By ElizaLeahy in forum WOODTURNING - GENERALReplies: 10Last Post: 29th March 2009, 03:35 PM -
Melting Metal In Microwave
By echnidna in forum METALWORK FORUMReplies: 0Last Post: 13th January 2009, 11:09 AM -
Melting metals in a domestic microwave
By echnidna in forum METALWORK FORUMReplies: 0Last Post: 13th January 2009, 10:04 AM -
Melting Lenses
By Chris Parks in forum WELDINGReplies: 8Last Post: 1st September 2007, 10:59 PM -
Melting Paraffin Wax
By DJ’s Timber in forum WOODWORK - GENERALReplies: 7Last Post: 28th January 2007, 09:49 PM