Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
10th August 2023, 08:42 AM #1Member
- Join Date
- Jul 2016
- Location
- Melbourne
- Posts
- 89
Bandsaw Choice - Blade Width Capacity vs Motor HP
I'm looking at a few different bandsaw models at around the $3k mark (new).
A good 14" model, cast iron wheels, solid base etc.
I don't envision cutting massive logs or anything, but I get 40-50mm hardwood boards that I would like to resaw into two 20mm boards.
It seems options are fairly limited and the main difference I'm seeing other than colour, is the blade width capacity (3/4inch vs 1inch) or motor hp (2hp vs 3hp).
The 3hp models have the lower capacity of 3/4 inch, whereas the 2hp can take the full 1inch blade.
I plan to get proper blades made up from Henry Bros or somewhere local in Melbourne.
Assuming I can't find one that does both for that price, which would you pick - wider blade or higher motor hp?
-
10th August 2023 08:42 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
10th August 2023, 03:14 PM #2Senior Member
- Join Date
- Oct 2010
- Location
- Drouin Vic.
- Posts
- 166
From my experience a very good quality blade from say McDivens here in Melb. such as their Tungsten blade is what I have been using for resawing work on a quality bandsaw for some time. Whilst I have been using a 27mm blade both at home and at my wood group with 3 Hp motors likewise smaller good quality blades at our club work fine with a 2 hp bandsaw. The other issue we have experienced is the ability to hold good blade tension especially with larger blades. It is therefore important to ensure you do purchase a quality saw with a strong frame if you are planning to do a lot of resaw work. Our club recently bought an industrial grade SCM bandsaw specifically for accurate resaw work and it also works just fine with the McDiven Tungsten blades.
Cheers,
Paintman
-
10th August 2023, 03:45 PM #3Senior Member
- Join Date
- Nov 2017
- Location
- Melbourne
- Age
- 73
- Posts
- 358
Try a personal visit to McDivens in Melbourne. I went there recently and they couldn't have been more helpful working out what I wanted to do (mainly resawing hardwood) with my first big (16") second hand bandsaw and providing the correct blade. I got a free lesson in various aspects of bandsawing. Won't be going anywhere else in future.
-
11th August 2023, 08:50 AM #4Member
- Join Date
- Jul 2016
- Location
- Melbourne
- Posts
- 89
Thanks for the tip about McDivens, definitely sounds like a worthwhile trip across town.
Now to just choose the bandsaw!
-
11th August 2023, 09:19 AM #5SENIOR MEMBER
- Join Date
- Feb 2018
- Location
- Shepparton
- Posts
- 508
Mc Diven in Melbourne are good and not to bad at Williamtown for Melbourne folks you can talk to them and they will recommend type of blade that fits the situation.As far as bandsaws go the more power and non flex is what to look for you be surprised at the useful uses you will find.
-
11th August 2023, 10:33 AM #6
I do a reasonable amount of resawing for panels for my boxes and only use a 1/2" 4 TPI bi-metal blade and never have any problems cutting straight nor the speed at which it cuts. I do these cuts on both soft and hardwoods up to about 180mm wide. My machine is an older Carbetec and I think it is only 1hp so it shows that resawing can be done with almost anything providing it is set up well. The club I go to has a slightly bigger Laguna with a 3hp motor which they run a 1" blade on and I often hear that one stall with pieces that are no where near the capacity of the machine.
Dallas
-
13th August 2023, 10:48 PM #7
The blade size is down to the frame of the machine as can it take the tension. Most makers tend to overstate the size blade the saw will take. Like Treecycle said a 12mm 3 or 4 tpi blade can do a fair job at resawing. Years ago I bought into the big blade advice only to find a smaller blade did a better job on my saw. Having the right tension is more important than the blade size. Horse power is also important so dont stint on that and of course blades need to be sharp. I also just use bymetal blades and I get a few resharpenings out of a blade. I can run a 16mm blade on mine but most times I run a 10mm 4tpi as an all round blade that can do most of what I want. Getting to your question I would go for the horsepower and run a blade that the saw can tension.
Regards
John
-
15th August 2023, 05:18 PM #8Member
- Join Date
- Jul 2016
- Location
- Melbourne
- Posts
- 89
Thanks - Great advice.
The machines I'm looking at are Sherwood, Carbatec, Woodfast level, they seem solid compared to my dinky 14" model on a stand - But not next-league level up in quality like a Felder, SCM etc. I had thought the largest blade would be the best bet, but perhaps HP and just a good, sharp 19mm blade is the way to go, or at least not any better/worse of an option.
Gives me a few more models to choose from.
Similar Threads
-
Over width bandsaw blade. Can it be used ?
By harry wall in forum BANDSAWSReplies: 5Last Post: 21st January 2017, 12:41 AM -
Bandsaw Blade Width Selection & Bandsaw bed throat and blade Alignment
By thumbsucker in forum BANDSAWSReplies: 30Last Post: 17th May 2014, 09:06 PM -
bandsaw blade width
By teepee1 in forum BANDSAWSReplies: 4Last Post: 13th August 2007, 11:17 AM -
SCMS - how much width capacity do you need?
By jmk89 in forum HAND TOOLS - POWEREDReplies: 6Last Post: 31st July 2007, 03:46 PM