Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 18
Thread: Need a bandsaw Dr
-
5th August 2022, 02:30 PM #1Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
Need a bandsaw Dr
I have a Halco Waoodmaster 355 bandsaw about two years old, I am not able to get blade to run true, the blade will sit perfectly on the top wheel (centre of tyre) but then the blade sits on the rim of the lower wheel and naturally comes of after a few minutes. Even when the guides are removed it occurs. When the blade is centred on the lower wheel, and placed in position on the top wheel the same thing happens. Can any one assist with my problem. Thank you.
-
5th August 2022 02:30 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th August 2022, 02:57 PM #2GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
When did this first start happening, was the blade changed and then it started?
How old is the blade?
Has the BS been apart for repairs?CHRIS
-
5th August 2022, 03:19 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,790
Sounds like there's no crown left on the wheels/tyres.
I'd like to see photos of what you think is the the band sitting correctly on the top and bottom tyres.
-
5th August 2022, 04:47 PM #4China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,474
I take it you are aware that the top wheel is adjustable to track the blade.
-
5th August 2022, 05:25 PM #5Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
Bandsaw Dr
The bs is two years old and the tyres on both wheels are good. I changed from a 1/2inch blade to a 1/4 around January this year and then it started, since then i have gone through three 1/4 blades by damaging them in the machine when they come off the wheel. The machine was new so no it has not been repaired.
-
5th August 2022, 05:59 PM #6GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
Does the 1/2" blade do the same thing now?
CHRIS
-
5th August 2022, 07:36 PM #7SENIOR MEMBER
- Join Date
- Dec 2012
- Location
- Australia
- Posts
- 684
Make any major setting changes when you first put the 1/2" blade on?
Could replace the wheel tyres but after only two years they shouldn't be a problem.
-
5th August 2022, 07:45 PM #8Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
No changes except for realigning the guides when i swopped to smaller blade and perhaps a small twinge of the top wheel.
spoke to mach8nery warehouse this afternoon, they suggest pulling the top wheel off and loomking to see everything there is tightly screwed together.
-
5th August 2022, 08:22 PM #9
Are you locking the tracking adjustment on the top wheel with the lock lever after adjustment?
Mobyturns
In An Instant Your Life CanChange Forever
-
5th August 2022, 10:41 PM #10Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
Yes, everything gets tighten after an alteration, tomorrow i shall strip it down and check if the two wheels are in enliinement, has been suggested that when assembled the tracking mechanism may be missing somethin. It came assembled so who knows who did what. Thanks everyone for your comments
-
6th August 2022, 07:33 PM #11Mobyturns
In An Instant Your Life CanChange Forever
-
6th August 2022, 08:12 PM #12Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
-
6th August 2022, 10:41 PM #13.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,790
-
7th August 2022, 03:58 PM #14Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
-
7th August 2022, 06:33 PM #15
Hate to disillusion you, but I suspect that the Jet comes from the same country, and quite likely the same manufacturer. You might be better organising to retrofit cheap and nasty screws/bolts with respectable ones throughout the existing saw.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
Similar Threads
-
Bandsaw questions- and identify my old bandsaw?
By MWF FEED in forum METALWORK FORUMReplies: 0Last Post: 22nd April 2020, 10:00 PM -
bandsaw blade supplier for home made bandsaw mill
By 19brendan81 in forum SMALL TIMBER MILLINGReplies: 26Last Post: 4th May 2018, 01:53 PM -
Minimax bandsaw and Kreg bandsaw fence
By Larks in forum BANDSAWSReplies: 0Last Post: 7th September 2017, 10:26 PM -
Bandsaw for only the SMARTEST of Buyers -Bandsaw in Excellent Condition
By prozac in forum BANDSAWSReplies: 4Last Post: 8th June 2008, 06:23 PM -
Will Carbatec bandsaw blades fit Jet bandsaw?
By FlyingDuck in forum BANDSAWSReplies: 2Last Post: 13th May 2006, 06:32 PM