Needs Pictures: 0
Results 1 to 7 of 7
Thread: Bandsaw Drift and Correcting It
-
27th July 2019, 12:24 AM #1GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
Bandsaw Drift and Correcting It
I posted this elsewhere but then realised I should have put it here as drift is a common problem and it need not be.. To read it in context look at this link
https://www.woodworkforums.com/f187/surprise-225034-post2150069#post2150069
I had a play tonight with my saw and did what I have recommended to Fletty and a few other people having trouble with their saws. I put two rare earth bar magnets on the blade and then stuck a 600mm steel rule to those, the magnets have to be clear of the teeth otherwise they won't be flat on the blade. I locked the fence to the rail and loosened the trunnion bolts to swing the table around but there was not quite enough movement and it left the fence still not parallel to the rule. European saws work a bit different to the generic Asian/US saws in that the tracking does not have the same adjustment as the Asian versions because the teeth have to hang off the side of the top wheel and the only function the tracking does is to get different width blades to that position. On my saw they have allowed for that and a fence adjuster can be seen in the photos and this aligns the fence to the blade. On an Asian saw the tracking would be changed if the table movement is not enough. Make sure all the guides are set in the running position with correct clearances also.
When I first set it up I looked at it and thought it was practically spot on until I measured from the rule to the fence and found about 20mm difference end to end and this had been doing a lot of resawing with no issues. It will be interesting to see what it is like when I do some more. I used the adjusting bolt and now it is spot on.
IMG_2305.jpgIMG_2306.jpgIMG_2304.jpgCHRIS
-
27th July 2019 12:24 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th July 2019, 09:10 AM #2
Good one - thanks for posting.
My BS does adjust for drift using tracking, but this is still a useful way to zero in on the correct position. Take magnets/ruler off, run saw for a minute so that blade settles down in new position on the wheel, reapply magnets and ruler, check against fence, adjust tracking position, rinse and repeat.
I'll be interested to see if cuts are actually drift-free when this method says that perfect alignment to the fence has been achieved, or are there any other factors at play? Obviously the blade will have to be at working tension when doing this.
-
27th July 2019, 11:31 AM #3GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
A blade that is poorly sharpened or perhaps has more set on one side or another will encourage drift. There was a batch of 25mm Resaw King blades that had been poorly sharpened when they were first introduced here that did this due to being badly made.
CHRIS
-
28th July 2019, 09:45 PM #4
You can also correct drift by adjusting blade tracking; at least on bandsaws with crowned wheels, I've never had a Euro saw with flat wheels. In my experience this matters more with larger width blades, which is what you are using for resawing.
-
29th July 2019, 01:06 AM #5GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
If the fence is parallel to the mitre slot the big advantage to moving the table ensures that the mitre slot has the same relationship to the blade as the fence.
CHRIS
-
23rd August 2020, 02:37 PM #6GOLD MEMBER
- Join Date
- Nov 2009
- Location
- Canberra
- Posts
- 1,301
-
23rd August 2020, 03:09 PM #7GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
Similar Threads
-
Bandsaw drift and fishtailing
By kenm46 in forum BANDSAWSReplies: 9Last Post: 29th May 2019, 08:20 PM -
eliminate drift from your bandsaw
By T91 in forum BANDSAWSReplies: 1Last Post: 24th August 2018, 07:35 AM -
Eliminating bandsaw drift
By Dengue in forum BANDSAWSReplies: 13Last Post: 30th January 2015, 03:23 PM -
Understanding bandsaw drift
By Dengue in forum BANDSAWSReplies: 20Last Post: 31st January 2012, 10:32 AM -
Bandsaw Blade drift
By woodcutta in forum BANDSAWSReplies: 2Last Post: 18th November 2004, 04:03 PM