Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 26
Thread: bandsaw being a total b#$%%
-
24th February 2008, 05:16 PM #1
bandsaw being a total b#$%%
Hi I need some help. I have a bandsaw that has me nearly totally bluffed of her. She keeps going bang. when it does this it is jamming and wood is being really grabbed. It a brand new blade. LIke it cannot even cut the length of a pen blank. I am nealy to afraid to use it. Any suggestion greatly appreciated on what could be going on?
Toni
-
24th February 2008 05:16 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
24th February 2008, 05:47 PM #2
Have you got your guides set properly.
Is the blade running in the centre of the wheels.
Do you have enought tension on the blade.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
24th February 2008, 07:28 PM #3
Is it the only blade you have, does the machine work better with one of the old blades, if so you have got a dud blade perahaps..
woody U.K.
"Common looking people are the best in the world: that is the reason the Lord makes so many of them." ~ Abraham Lincoln
-
24th February 2008, 09:14 PM #4
You can get this if the blade has cracked or is kinked.
Try turning it by hand to identify when and where the noise is ocurring.- Wood Borer
-
24th February 2008, 10:10 PM #5GOLD MEMBER
- Join Date
- Oct 2005
- Location
- Adelaide
- Posts
- 1,024
Sounds like a tooth or two on the blade is way out of whack.
I'd disconnect the power and do as WB suggests. Just turn it over in the normal direction while closely watching the blade as it runs past the guides. Whatever is causing the problem should be very obvious.
woodbe.
-
25th February 2008, 04:37 PM #6GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 1,610
Toni,
are you cutting straight, or gentle curves, or tight curves?
Does it happen on different types of wood?
Does it happen as soon as you start cutting, or only after you've used the saw for a while?
Are you cutting wood laying flat on the table, or are you cutting round sections of wood?
Cheers,
Andrew
-
25th February 2008, 09:36 PM #7
Hi Andrew, does not matter straight, curved, what kind of wood. it does not matter how long I been cutting it usually within the first 2" and she will grab and it square pieces flat on the table still grabs. I am so close to never using it today. I even contemplated just going to buy a new baby gmc bandsaw because it did all that I asked of it
Toni
-
25th February 2008, 10:05 PM #8
Did you post a thread earlier on this machine, re setting up of blade drive wheels?
woody U.K.
"Common looking people are the best in the world: that is the reason the Lord makes so many of them." ~ Abraham Lincoln
-
25th February 2008, 10:39 PM #9
no I don't think so.
Toni
-
25th February 2008, 11:00 PM #10
I'm sorry I don't understand this talk of a bandsaw going "bang"!
What bandsaw are you using, what are you using it for?
When you say "within the first 2 inches and she will grab and it square pieces flat on the table still grabs" sorry I don't understand?
Many questions, but we are here to help!
Good HealthTony Ward
Now a power carver and living the dream.
-
26th February 2008, 02:18 PM #11GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 1,610
Hmmm...
the only time my bandsaw has gone "bang" was when cutting a curved branch, and as it fed through the cutting point lifted off the table, and the saw promptly whacked the branch back down onto the table.
Hence my question about round vs. flat.
I've only had one "grab" and that was cutting green timber. As I cut through a knot, the blade started squealing, steam came out of the cut, then the blade stopped but the motor kept trying.
The wood clamped onto the blade so hard it kinked it.
In your case, given that it happens with various woods implies it's either the saw, or the blade.
I'm wondering if your table is warped, or your insert is not bedded properly.
So once the wood gets past the 'pivot point', the blade slaps it down onto the table. The angle of the wood changes, and it can grab. (See pics for what I'm thinking).
If not this, then can you swap to a different blade?
Cheers,
Andrew
-
26th February 2008, 08:39 PM #12
Hi Tony it literally makes a bang sound literally goes clunk and then grabs that wood like no tommorrow. The wood is flat on the table. It jams the blade when it happens which caused the wood to get damaged
Perhaps you are right. I will get hubby to have a look at it for me
Toni
-
26th February 2008, 08:40 PM #13
-
26th February 2008, 08:48 PM #14
Or the lower blade guides way out together with a kink on the blade as well.
woody U.K.
"Common looking people are the best in the world: that is the reason the Lord makes so many of them." ~ Abraham Lincoln
-
26th February 2008, 08:56 PM #15
Check where the blade is welded. Does the blade protrude at the back or front? Hold a pencil to the back of the blade while running, can you feel a ticking?
Do the teeth point in the same direction at the weld instead of alternating?
Check the blade is seated properly on the rear bearing and not rolling off.
Check there is sufficient tension on the blade.
Where did you get the blade, how many tpi is it?
EDIT: This post assumes you checked the blade isn't bent or kinked (as Bob said) that would be my first suspicion, particularly if the saw worked up until that blade was fitted.
Similar Threads
-
Total Noob
By funkychicken in forum WOODCARVING AND SCULPTUREReplies: 17Last Post: 17th September 2007, 10:06 PM -
2hp D/C Total Tools vs C/Tec
By Chesand in forum HAND TOOLS - POWEREDReplies: 4Last Post: 10th December 2005, 07:12 PM -
Total Tools
By NewLou in forum Links to: TIMBER & HARDWARE SUPPPLIERSReplies: 2Last Post: 12th October 2004, 10:07 PM -
total cad
By jow104 in forum DESIGNS & PLANS FOR PROJECTSReplies: 3Last Post: 11th July 2004, 08:21 PM -
Total Tools
By Dean in forum Links to: WEB SITESReplies: 2Last Post: 28th February 2004, 10:43 AM