Needs Pictures: 0
Results 1 to 7 of 7
Thread: Transporting a bandsaw
-
7th July 2022, 10:15 PM #1
Transporting a bandsaw
I've just bought my first bandsaw, a Rikon 10-353, and I need to get it home. My question is; can I lay it down or must I transport it upright?
-
7th July 2022 10:15 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
7th July 2022, 10:18 PM #2
Laying it down should be no problems. It is not like a fridge, where you can upset the gas. Just make sure you don't squash any of the sheet metal or switches.
I am learning, slowley.
-
7th July 2022, 11:02 PM #3
Lay it down on it's spine, remove the table and strap it down tight!
Pat
Work is a necessary evil to be avoided. Mark Twain
-
8th July 2022, 12:09 AM #4
Removing the table is the important bit as its easy to break the trunnion. Never try lifting by the table either for the same reason. New bandsaws normally come laying flat and boxed up with the table seperate for you to bolt on.
Regards
John
-
8th July 2022, 09:08 AM #5
Thanks for all the advice!
-
8th July 2022, 10:06 AM #6SENIOR MEMBER
- Join Date
- May 2013
- Location
- Auckland, New Zealand
- Posts
- 997
SCM L'Invincibile si X, SCM L'Invincibile S7, SCM TI 145EP, SCM Sandya Win 630, Masterwood OMB1V, Meber 600, Delta RJ42, Nederman S750, Chicago Pneumatics CPRS10500, Ceccato CDX12
-
9th July 2022, 08:47 AM #7Senior Member
- Join Date
- Apr 2017
- Location
- Éire
- Age
- 39
- Posts
- 300
As said table off first, switches if necessary, prop up the guide side if your small and can get no leverage, i.e something like a 3" thick fence post will make a big difference in regards to effort required.
Walk around the other end and tip it down on the column (frame).
I will add, not to put a fulcrum anywhere under the column when laying it down,
i.e nothing between the base of the machine and the post at the end which you are laying it down onto.
The base has a wide footprint, and provides stability, as it can roll otherwise, ie don't eliminate it's effectiveness by raising the base off.
see my "tippy saw" thread,
fair enough this happened whilst the machine was orientated the other way,
but highlights that the column is not likely to be flat, and likely a bit bulgy up the centre and prone to rolling.
Another thing possibly to be careful about if tipping up the saw, should you be very light, and the floor be very uneven,
then tipping it up near a wall (motor side facing wall) might be some insurance should it take a real bad shake when plonked upright.
I noticed a bit of this first time moving my machine, a combination of circumstances led to a recipe for the possibility.
Sloping floor in the folks shed/combined with machine sitting taller on a mobile base with adjusted feet to suit, I forgot to level the base beforehand
and the base of my machine was a bit shoddily also, should you have opportunity to do a one finger tippy test beforehand pressing on the door.
Get some carpet or cardboard o keep the paint in good condition
All the best
Tom
Similar Threads
-
Transporting oxy-acetylene
By MWF FEED in forum METALWORK FORUMReplies: 0Last Post: 13th October 2019, 12:40 AM -
Transporting machinery
By chode in forum WOODWORK - GENERALReplies: 5Last Post: 27th May 2016, 06:53 AM -
Transporting Lucas Mill
By asheddie in forum SMALL TIMBER MILLINGReplies: 9Last Post: 20th December 2015, 11:14 AM -
Transporting the auk
By wavedancer in forum MISC BOAT RELATED STUFFReplies: 0Last Post: 5th August 2010, 07:44 PM