Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Cheap handy AC met power
-
7th May 2013, 10:58 PM #1.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,787
Cheap handy AC met power
My Son wanted something that he could monitor the power consumption of his home server which has 20 hard drives in it so I knocked up the simple extension cord with a built in V/I AC meter. It's only good to 100 mA on the current but that's more than enough for him. I wired a switch in line with the power supply line so the display so it could be turned off when not required.
The panel meter is $8 on ebay - I bought 4 more because I will add these to a couple of machines WIGRTI.
Very easy to wire up, just have to cut the active line and pass it through the sensing coil and rejoin it again.
The earth line and the neutral stay intact except the neutral line needs to be exposed to provide a connection to run the meter along with another connection to active.
It could be added to any machine with very little effort.
Here it is monitoring the warm up power drawn by my coffee machine - fortunately the coffee machine has a 8:1 duty cycle so it not always so thirsty on the juice.
-
7th May 2013 10:58 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th May 2013, 11:15 AM #2
Damn you BobL. Now I have to go and soend more money on eBay.
Bob Willson
The term 'grammar nazi' was invented to make people, who don't know their grammar, feel OK about being uneducated.
-
8th May 2013, 12:51 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,787
Yeah I've watching this one while I make coffees and dreaming up applications and I reckon these things are going to be really useful.
I was thinking to add these onto some of the power lines of my breaker box and maybe even one to the whole mains switch as they is supposed to be rated to up to 50A.
Come to think of it why aren't these STANDARD on expander boards to save the headache of the damn things tripping out?
-
16th May 2013, 11:47 PM #4SENIOR MEMBER
- Join Date
- Oct 2008
- Location
- N.W.Tasmania
- Posts
- 703
-
16th May 2013, 11:53 PM #5.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,787
-
17th May 2013, 01:04 AM #6SENIOR MEMBER
- Join Date
- Oct 2008
- Location
- N.W.Tasmania
- Posts
- 703
Ah thanks for my edification, and that is a nice and tidy installation there too. You will probably find that you will be able to tell when it is time to empty your DC and clean/replace your filters by watching the current draw with no dust being conveyed, but the system running.
Actually I am looking for some similar measurement system for my camper trailer, to check the state of batteries and charge rate of a proposed solar panel but as LEDs glow brightly in the dark, I may just settle for old fashioned analogue meters, so as not to disturb our sleep.
Regards,
Rob.
-
17th May 2013, 01:23 AM #7.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,787
I'll be monitoring it. A blocked filter is equivalent to all blast gates closed where the current drawn drops as the impeller stalls and is churning rather than transporting air so it does less work. The difference is quite marked. About 9.2 A with all blast gates open and 6.5A with them all closed.
Actually I am looking for some similar measurement system for my camper trailer, to check the state of batteries and charge rate of a proposed solar panel but as LEDs glow brightly in the dark, I may just settle for old fashioned analogue meters, so as not to disturb our sleep.
-
17th May 2013, 05:47 AM #8
For those with less skill then bob............... For $20
https://zazz.com.au/daily/thingy/7122vapourforge.com
-
17th May 2013, 09:44 AM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,787
-
18th May 2013, 08:33 PM #10
For anyone near an ALDI, they had their power meter this week at $14.99, and their RF remote switches at (I think) $19.99.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
Similar Threads
-
Back flattening - horse power rather than hand power
By rsser in forum SHARPENINGReplies: 45Last Post: 21st April 2012, 04:42 PM -
cheap GMC and Ryobi power tools in Melbourne
By ftje in forum HAND TOOLS - POWEREDReplies: 13Last Post: 22nd October 2007, 09:15 AM -
Cheap power tools and hardware
By Guy in forum HAND TOOLS - POWEREDReplies: 0Last Post: 22nd June 2004, 11:35 PM -
cheap power tools - WOFTAM
By Zed in forum HAND TOOLS - POWEREDReplies: 5Last Post: 24th May 2004, 09:49 PM -
Cheap Power Tools
By Blunt Saw in forum HAND TOOLS - POWEREDReplies: 14Last Post: 10th September 2003, 09:38 PM