Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Carbatec 6" Long Bed Jointer
-
2nd December 2013, 01:28 PM #1Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
Carbatec 6" Long Bed Jointer
Carbatec 6" long bed jointer in a very good condition. Older model in grey colour, about 5-6 years old.
- No rust, very clean well looked after surfaces.
- New tungsten blades (18% Tungsten Thicknesser & Jointer Blades : CARBA-TEC), they have done only a couple of test cuts on pine battens.
- I added hinges to the side of the jointer so that the inside of the stand can be used for storage.
The same model with new colour scheme, but mechanically looking identical is this one: Carba-Tec® 6" Long Bed Jointer : CARBA-TEC
Pictures to follow tonight. Cash on pick up in Canberra.
-
2nd December 2013 01:28 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd December 2013, 07:18 PM #2Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
Here is a couple of photos.
-
4th December 2013, 11:58 PM #3
Hmm do that fit in your car???
DANGER!!!!I'm Dyslexic Spelling may offend!!!!!
-
5th December 2013, 08:09 AM #4Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
Probably, but it will be hard to put it there, it is fairly heavy. Trailer is much easier...
-
5th December 2013, 08:29 AM #5Intermediate Member
- Join Date
- Jan 2009
- Location
- Gundaroo
- Posts
- 41
hi Ilya,
Could I come over and have a look at some stage?
Cheers
Kim
-
5th December 2013, 08:37 AM #6Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
-
7th December 2013, 08:33 AM #7Intermediate Member
- Join Date
- Jan 2009
- Location
- Gundaroo
- Posts
- 41
Hi Ilya,
I appreciate the time you took showing me your machine - very tidy and well looked after. I think at this stage I'll hold off and buy a bigger machine.
Regards
Kim
-
7th December 2013, 01:53 PM #8Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
Hi Kim,
Thanks for letting me know. I think this is right decision, seeing that you mainly need to plane wider boards. Probably 8" will still be a bit narrow!
Regards,
ilya
-
15th December 2013, 06:32 PM #9Senior Member
- Join Date
- Aug 2008
- Location
- Canberra
- Posts
- 420
Still available
Similar Threads
-
How do I tune Carbatec 8' Long bed jointer?
By q9 in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 15Last Post: 6th November 2011, 07:15 AM -
JET 6" deluxe long bed jointer.
By Robo1 in forum GENERAL & SMALL MACHINERYReplies: 10Last Post: 22nd December 2007, 07:55 PM -
6" Long Bed Jointer
By Mr Brush in forum HAND TOOLS - POWEREDReplies: 6Last Post: 29th August 2006, 10:38 AM