Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Jet 20" Bandsaw
-
2nd October 2014, 10:30 PM #1or maybe a bit later
- Join Date
- Apr 2006
- Location
- Brisbane
- Posts
- 48
Jet 20" Bandsaw
I am selling my trusty Jet 20" Bandsaw. Shows its age a bit but works really well. Plenty of grunt - it needs 15A power. 340mm resaw capacity. 510mm width. Takes up to 38mm blades. Tilting table. Foot brake. 4" dust extractor port. Ball bearing guides top and bottom. Mitre slide. Very solid fence. Original manual.
Comes with some blades including a 3TPI 25mm bi-metallic resaw and an unused 14TPI 25mm.
I have no logical reason to sell - I just have my heart set on the new Laguna!
Asking $890 but let me know if I'm dreaming.
GraemeGraeme
If you're totally in control then you are going too slow.
-
2nd October 2014 10:30 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd October 2014, 11:40 PM #2
-
3rd October 2014, 12:16 AM #3
Hi Graeme,
I'm interested in your bandsaw and had a few questions. Can you tell me the dimentions of the footprint and where are you located?
Thanks
Denim.Last edited by Denim; 3rd October 2014 at 12:17 AM. Reason: Just read that it's 3 phase.
-
3rd October 2014, 02:09 PM #4or maybe a bit later
- Join Date
- Apr 2006
- Location
- Brisbane
- Posts
- 48
Hi Denim,
Bandsaw is located in Hawthorne, Brisbane. For clarity, the power supply requirement is single phase 15A. I'll post the footprint when I get home from work tonight. Comes with permanent wheels that allow you to wheel it away from the wall and back again but the wheels don't swivel (and it is a solid lump to manhandle).
I'll PM phone number.
Regards
GraemeGraeme
If you're totally in control then you are going too slow.
-
3rd October 2014, 08:50 PM #5or maybe a bit later
- Join Date
- Apr 2006
- Location
- Brisbane
- Posts
- 48
-
3rd October 2014, 09:29 PM #6
Hi Graeme,
Thanks for the info. I'd love to take this off your hands but it's just a little too big for my workshop unfortunately so I'll have to pass.
Denim.
-
4th October 2014, 08:59 PM #7
...a pic of the compliance plate please
-
4th October 2014, 10:35 PM #8or maybe a bit later
- Join Date
- Apr 2006
- Location
- Brisbane
- Posts
- 48
-
5th October 2014, 03:12 PM #9or maybe a bit later
- Join Date
- Apr 2006
- Location
- Brisbane
- Posts
- 48
SOLD
The saw has been sold.
Graeme
If you're totally in control then you are going too slow.
Similar Threads
-
Woodfast 18" bandsaw & 10" jointer - photos of flyer & what is the blade length?
By StevenManos in forum BANDSAWSReplies: 7Last Post: 20th November 2013, 07:35 AM -
WIP - Restoration of an 1960's (?) Toolmac 14"" Taiwanese Bandsaw
By GarciaJ in forum BANDSAWSReplies: 22Last Post: 22nd October 2012, 10:30 PM