Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 41 of 41
Thread: Burdekin Plum backsaw.
-
5th December 2013, 10:57 AM #31Member
- Join Date
- Mar 2012
- Location
- Doe Run, Pennsylvania
- Posts
- 91
-
5th December 2013 10:57 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th December 2013, 11:01 AM #32
-
5th December 2013, 11:10 AM #33
-
5th December 2013, 11:13 AM #34
Thanks Isaac,
Yes, that's the one! nice find. I can stop looking now..
He is measuring a different angle, but I think it's easily converted, probably, (90 - BBrode_hang_angle) andaddsubtract a correction for canted blades, the reason I think he is measuring the wrong angle, is that "higher" hang angles would be lower numbers with his method. I would have liked to know the lengths of the saws he measured.. maybe a good research topic to see how hang angle relates to blade length in 18th and 19th century saws.
Regards
Ray
PS Sorry for the thread hijack Stewie,...
-
5th December 2013, 02:49 PM #35
There is a whole thread starting here ... Handsaw Handle Angles - Open Handled *PIC*
that I haven't doven into yet
And again apologising to Stewie ... one little aside to Isaac ...
your blog models force as acting along the line of the hang ... or perpendicular actually ... and I'm not sure I agree with that.
Obviously the resultant motion is basically back and forth only ... hmmm .... I don't want to disturb this thread.
I'd better go read them again and think about it some more.
Cheers,
Paul
-
5th December 2013, 03:08 PM #36
This is quite common on the net so ... has anyone mentioned ...
" it seems to me that the hang angle, should be such that your index finger points towards somewhere around middle of the tooth line, if you follow this general argument then it seems logical that shorter saws will have higher hang angles, and longer saws would have lower hang angles, (I'm measuring the hang angle as angle between the line of the grip to a line at right angles to the tooth line) So a high hang angle is typically a small dovetail saw, and a low hang angle is typical of a normal handsaw. "
Also ... for Ray ... not a lot left ...
Bob Brode -- A gallery of tools
Bob Brode
Cheers,
Paul
-
5th December 2013, 03:25 PM #37Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi all. I completed some more work on the Burdekin Plum backsaw today. As you will the blade has been shaped and fitted, as well as the fit of the brass back within the handle. Both the tenon as well as the mortise within the handle have been stepped similar to how Pedder & Klaus do on some of their backsaws. Just a not with the blade used. It one of a number that Ron Bontz sent to me as a gift a while ago. All pre-toothed. This blade is 0.025 plate, after shaping the heel has a 10" tooth length, and is 70mm in depth. Its been and toothed at 14 tpi, with a 25 degree rip tooth. I have also scribed 2 horizontal lines to each face of the brass back so it can be later shaped with 2 deep bevels. If this doesn't look quite right I still have the option of rounding these off. I still have to complete the final smoothing off with the shellac finish on the handle, but I leave this till the end of the saw build.
Stewie;
-
5th December 2013, 03:49 PM #38Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi Paul. At what point of the tooth line the index finger points to is a major debate by itself as some saw makers prefer a higher set handle in general, whereas others like myself prefer it lower set so that the wrist is more in a horizontal line to the tooth line. Probably best to raise a new post on that one as you may end up with a major influx of replies debating the pro's and cons. Isaac has some good information about this topic on his website that covers correct posture & working height in relation to best hang for a backsaw. There are so many variables including the general height of the user that make this topic rather difficult come up with 1 single answer to correct hang. The final answer may be it just come down to finding the right backsaw that suits you the individual. It gives me a headache just thinking about the whole debate. But certainly worth the effort to hear all the differing opinions.
Stewie;
-
6th December 2013, 10:21 AM #39Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi. I have moved this thread to the new dedicated Saws - Handmade, sub forum.
I would also like to personally thank Ian () and Neil for their support in making this forum listing available to further meet the needs of our forum membership.
Stewie;
After a few requests by members that make their own tools we have put in sub Forums under Homemade tools and jigs for the saw and chisel makers here:Saws- handmade and here: Chisels-handmade
The Mods and Admins will be moving threads across to these Forums but if you see a thread or post pertaining to these activities that we miss can you post a link here and it will be moved. Thank you.
-
6th December 2013, 11:19 AM #40
-
6th December 2013, 02:07 PM #41
Similar Threads
-
Small Burdekin Plum
By pjt in forum SMALL TIMBER MILLINGReplies: 11Last Post: 19th November 2012, 08:51 AM -
Burdekin Plum Bowl
By smiife in forum WOODTURNING - GENERALReplies: 10Last Post: 22nd June 2011, 10:59 PM -
Burdekin plum
By chowcini in forum TIMBERReplies: 4Last Post: 10th August 2010, 09:10 PM -
Burdekin Plum
By Terrymac in forum WOODTURNING - GENERALReplies: 13Last Post: 21st July 2009, 07:43 PM -
Help looking for some Saffronheart, Red Condoo and Burdekin Plum
By shadowformz in forum WOODTURNING - GENERALReplies: 13Last Post: 3rd January 2008, 11:51 AM