Page 2 of 2 FirstFirst 12
Results 16 to 18 of 18
  1. #16
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    73
    Posts
    11,099

    Default

    Quote Originally Posted by delbs View Post
    good to hear it arrived, the question is would you order it from there again?

    how do you personally attack that material to cut to the size of the blade you require? find that hacksaw works or something like a small dremel bit can cut it noting to keep heat away etc to not warp the edge

    Cheers,
    Nathan

    Nathan

    I am not sure how Matt will be doing this as he may be locked down away from his tool base. Most people use an angle grinder with a thin (1mm) cutting disc. They cut through this thin steel so quickly that almost no heat is transmitted to the point that the cut edge can be held with bare fingers. An added precaution is to clamp the saw plate between heavier section steel to act as a heat sink. The top piece of steel acts as a guide for cutting too. See post # 8 in this thread for some pictorial idea of the process.

    The plates can be cut with a fine (32ppi) hacksaw blade when other methods are unavailable.

    Regards
    Paul
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #17
    Join Date
    Nov 2011
    Location
    Melbourne
    Posts
    6,975

    Default

    Quote Originally Posted by delbs View Post
    good to hear it arrived, the question is would you order it from there again?

    how do you personally attack that material to cut to the size of the blade you require? find that hacksaw works or something like a small dremel bit can cut it noting to keep heat away etc to not warp the edge

    Cheers,
    Nathan
    Nathan, Paul is right and wrong, I’m currently away from Creative Den, but I’ve created a Sub den to feed my tool needs.

    I haven’t used any of the spring plate yet, but plan on using it very soon.
    Now that the Plane challenge is done an dusted, I may get stuck into it.
    With regards cutting the steel, the really thin stuff under .5 mm I’ve used a large pair of Tin snips in the past, but I’m a maverick.
    Paul is on the money if your comfortable using a small angle grinder with a thin cut of disk, they will do the job well.
    I’m comfortable using small or big angle grinders, I just hate the noise an sparks and all the carry on(snob)

    Cheers Matt.

  4. #18
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,757

    Default

    It's not needed for something thing like saw plate but otherwise this variable speed thin kerf mini table saw is the ducks nuts for cutting any tool steel.
    Cuts are pretty accurate especially if the mitre is used.
    bestofthebest.jpg

    Because the grinder that drives the cutting wheel is sealed and the wheel is separated from the grinder by a belt I can even drip water into the cut line.
    It makes a mess but I can cut quite thick tool steel without it bluing.

    Sorry don't have a photo but here's one when I was using my old 8" table saw with the water cooling attachment.
    Watercooledsaw.jpg
    Attached Images Attached Images

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Frames Saws/Bows Saws for re-sawing small boards 100mm deep
    By Kate84TS in forum HAND TOOLS - UNPOWERED
    Replies: 29
    Last Post: 15th April 2017, 03:15 PM
  2. Pretty little thing
    By orraloon in forum HAND TOOLS - UNPOWERED
    Replies: 13
    Last Post: 1st September 2010, 12:10 AM
  3. Far from pretty
    By corbs in forum WOODTURNING - GENERAL
    Replies: 10
    Last Post: 13th January 2010, 08:27 PM
  4. Pretty in pink
    By bdar in forum WOODTURNING - PEN TURNING
    Replies: 10
    Last Post: 13th August 2007, 06:50 PM
  5. pretty pussy
    By Christopha in forum WOODIES JOKES
    Replies: 1
    Last Post: 15th November 2003, 04:53 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •