Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 29 of 29
-
11th September 2015, 04:40 PM #16
-
11th September 2015 04:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
11th September 2015, 07:09 PM #17
A Timely Thraed
Boy is this thread timely !!! Today I won this Preston Woodworking Machinery Co. (Canada) bandsaw, with 30" wheels.
Preston1.jpg Preston2.jpg
On Monday I'll remove the two doors; the guards; the upper wheel; and the table (seeing as broken table trunnions seem to be a regular occurance ). I have to remove the upper guards and upper wheel, as the machine stands ~2.5m high and the ceiling in my garage is ~2.3m (I'll be cutting a slot in the ceiling when I've got it in its final location (the joists above are 300mm deep)
I'm not sure whether to use a truck with hi-ab, because it won't fit down the driveway, and I had a major hassle with my Wadkin PK two months ago... https://forum.canadianwoodworking.co...in-PK-Marooned (you may need to join that forum to see the pictures)
...or to get a mate to take it on his big trailer - which has a winch and the ability to unload by tipping (direct into my garage). This is only an option because of the short distance - about 6km - so we can do two trips.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
11th September 2015, 07:32 PM #18
Lovely bandsaw there Vann, congratulations! Maybe needs to go in Mattys' thread too?
Are the towing laws for brakes on the trailer much different in Australia than the UK? Here we can tow 750Kg unbraked and upto 3500Kg braked, and that would be an 'over run' breaking system, so no link with the vehicle brakes, just a damped telescopic hitch that applies the trailers brakes mechanically. The vehicle plate has four weights listed, 1 & 2 being vehicle maximum axle weights, 3 the vehicles max gross weight (always slightly less than the sum of 1 & 2), and the 4th weight being 'Gross Train Weight', being the all up weight of combined vehicle and trailer. When you get pulled in that's the one they look at most keenly, as long as your under that and looking reasonable it seems fine.
-
11th September 2015, 08:56 PM #19
Thanks, I think it's rather ugly myself. I've been on the lookout for a Silver/Cresent (preferably a 24"), but in this neck of the woods I think I'd be waiting a long time...
I don't know if this would be allowed in Matty's thread. Are Canadians really American?
To be honest I don't know how much weight is legal here in New Zealand (I could always look it up I suppose). This bandsaw must weigh the best part of a ton. I don't think it would legal behind my 1800cc Corolla. My mate has a big Dodge (wrong side drive). His trailer only has a single axle (uses the same wheels as his Dodge), so I don't think t would be wise to go too far with a load like this.
In the end it will be up to him. But it's only 6km...
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
11th September 2015, 10:13 PM #20SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
For me I go centre and slightly forward.
Another thing worth mentioning if your new to tying a load, is to pull over down the road a bit to check the load has not shifted and that the ropes/straps are all still tight.
If your going with straps, I would again recommend backing them up with some ropes, it will be very cheap insurance with a trip that long. Sorry I have trust issues with straps.
If your hiring a trailer, another thing to add to the checklist is to inspect it thoroughly before taking it (tires, lights, tow hitch, safety chain, brakes, wheel nuts, springs, etc.). I've seen some pretty bad, even what I would consider unsafe hire trailers (that's not to say they are all bad).
cheers,
Camo
-
24th September 2015, 02:40 PM #21
God thread and good tips on tying down and securing the load. How have you guys loaded and unloaded these beasts? How many guys are needed to safely move one?
…..Live a Quiet Life & Work with your Hands
-
24th September 2015, 06:24 PM #22Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
-
24th September 2015, 08:46 PM #23
Mine got lifted off its foundation of the last 25 years, by a forklift truck - but not using the tynes. Instead the operator had an attachment that went on the tynes effectively turning it into a crane. He used a soft sling around the upper part of the main casting (near the top wheel support) and gingerly lifted it off. It didn't break the casting (but I did wonder if it might ).
Then to get it off the trailer, it was lifted the same way, using a hiab to lift it onto a truck, and back off again into storage (where it is still).
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
24th September 2015, 09:13 PM #24
Vann, have you fut a hole in the roof yet to get it in??
…..Live a Quiet Life & Work with your Hands
-
26th September 2015, 11:46 PM #25
I've transported a Woodfast BS500 (19") which is nowhere near the weight of the Wadkin. Also removed the table & trunions. BS's are difficult to secure well.
One thing I would suggest is purchasing a couple of 200 x 75 mm or 100mm sleepers to bolt to the feet of the bandsaw. Bandsaws don't have a very large machine footprint and are also relatively top heavy. On a long road trip the machine will move no matter how well strapped it is. Rubber matting will help.
Cut the sleepers to a length just short of the width of the trailer. While you have the machine lifted off its present footing for loading, temporarily lower it down onto the sleepers, mark the holes, lift it up again, then drill the holes and countersink the bottom side of the holes for the bolt heads. Then slide the sleepers back under the machine with bolts inserted, lower machine, do up bolts, load into trailer. This will remove the sideways movement and if you cut some dunnage to size you can also take care of any fore and aft movement as well. Secure the BS with straps etc.
https://www.nobles.com.au/getattachm...raint.pdf.aspxMobyturns
In An Instant Your Life CanChange Forever
-
25th October 2015, 03:13 PM #26
How to transport a non-Wadkin bandsaw
I took delivery of my bandsaw this morning. It came on a truck all strapped down.
Ar1.jpg Clive had already removed the restraints by the time I remembered my camera.
The big hunk of cast iron to the left of the saw is the motor stand. I'd left it on while being transported, for extra stability.
Ar2.jpg Lucky that 4"x4" fenceposts are cheap.
I'd measured up the saw and knocked-up this wooden cradle for the trip down the driveway.
Ar8.jpg
Then using the car to restrain it, we rolled it down on 25mm OD heavy wall pipe rollers.
As7.jpg As5.jpg Just some gratuitous tool
Also on the truck was a Bridgeport mill and a Colchester lathe. They weren't for me.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
26th October 2015, 10:53 AM #27SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
-
26th October 2015, 11:13 AM #28Intermediate Member
- Join Date
- Feb 2011
- Location
- melbourne
- Posts
- 34
i too have a dr30 that i had to move. my advice if possible, is to remove the 3 large bolts that secure the top wheel and its adjustment mechanism to the main neck of the machine. firstly,its come off easily and it doweled in place for future reassembly and perfect alignment, just be wary of damaging the dowels when lifting the wheel off. the other advantage is how dramatically it lowers the centre of gravity. also remove all guards. At all costs, i would avoid restraining the machine from anywhere on the neck, except for at the very base of the neck close down to the main body, you don't want stress on this point, especially if you hit a bump in the road. the straps will be pulling one way and the saw will be wanting to go another. if you remove the weights from up to, the neck can travel stress free. i also bolted two large posts under my machine to increase its footprint and act like runners to allow it to be roller into the workshop on pipe. if you need any other help. dimensions act, let em
-
26th October 2015, 03:16 PM #29
Similar Threads
-
Lathe transport
By Acey124 in forum THE HERCUS AREAReplies: 13Last Post: 4th March 2014, 09:29 AM -
Transport suggestions
By Larkan in forum BOX MAKINGReplies: 1Last Post: 30th July 2013, 05:18 PM -
Wadkin Bursgreen BZB 20/500 Bandsaw
By camoz in forum ANTIQUE AND COLLECTABLE TOOLSReplies: 12Last Post: 17th June 2013, 10:36 PM -
Bandsaw transport required - Sydney to Melbourne
By monoman in forum BANDSAWSReplies: 0Last Post: 22nd March 2009, 09:55 PM