Needs Pictures: 0
Results 1 to 7 of 7
Thread: Dyco Superfine 12" Table Saw
-
6th May 2024, 04:42 PM #1New Member
- Join Date
- Apr 2024
- Location
- Auckland, NZ
- Posts
- 7
Dyco Superfine 12" Table Saw
Hi All!
Got this table saw here in Auckland, NZ for a very good price (NZD 225.00 delivered) and I am restoring it. I am going to use this thread to document the whole process.
It seems to be complete, but a lot of parts are rusty and very very dirty, here are some pictures from the previous owner:
2110949216.jpg2110949225.jpg2111575767.jpg2110949227.jpg2110949224.jpg
And these are from me after I started disassembling it:
270b6579-d45a-42a4-96e3-dbe353f8e43a.jpegeefcab5b-acef-4667-beaa-f338bb9a93eb.jpegfa5428c8-d374-49d8-bd17-084dfe66fca0.jpeg2764e0e4-d990-4589-9ace-37bc36f61b80.jpeg522b8271-3f2f-4dff-90e0-339420924ccc.jpeg21acb2ce-d147-4e27-8146-7101998ff27a.jpeg
This is by far the most ambitious project I have ever made, wish me luck!
-
6th May 2024 04:42 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th May 2024, 04:51 PM #2New Member
- Join Date
- Apr 2024
- Location
- Auckland, NZ
- Posts
- 7
Some things that I need to figure out
Some things that I need to figure out:
- I am going to use a VFD for it, I created another thread for that in the ELECTRONICS section.
- I need to remove the arbour shaft to replace the bearings, but it doesn't move. I have removed all the the pins and bolts from the pulley, but it simply don't move... Any tips? Here are some pictures:
b80cb9eb7.jpeg100b9c8ad7eb.jpeg88f01c98ee6f.jpeg3fdc5be5ab27.jpeg
-
7th May 2024, 12:09 AM #3GOLD MEMBER
- Join Date
- Apr 2012
- Location
- Sydney
- Posts
- 1,504
Judging by the broken casting looks like someone has tried to remove it previously with a rather large hammer
-
7th May 2024, 01:00 PM #4SENIOR MEMBER
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 649
Good project! Mine was a fun - Dyco 12" Table Saw. I did replace the 3-phase motor with a single phase 240v motor. This worked well but from memory required a basic mounting plate made up to interface with the original bracket from the saw.
-
8th May 2024, 02:15 PM #5New Member
- Join Date
- Apr 2024
- Location
- Auckland, NZ
- Posts
- 7
Hey Charlie! I know it! Hahaha, I even added you on LinkedIn to talk about this (sorry BTW).
To keep it cost effective I am going to use a VFD since it is hard to find a B5 flange single phase motor here in NZ for less than 300 dollars (I am going to pay 79 on the VFD at AliExpress).
It is an amazing project though, I am really enjoying the process
Cheers!
-
8th May 2024, 07:35 PM #6New Member
- Join Date
- Apr 2024
- Location
- Auckland, NZ
- Posts
- 7
Update about the arbor: I did it! 😅
I bought this bearing puller and it is amazing! Really well made and relatively cheap: NZD 50.00, very heavy-duty.
bearing-puller.jpg
After I removed the shaft from the housing, I had to remove the bearing from the shaft and then a new issue arose: how to remove a stuck shaft woodruff key? In my case I kept pulling the bearing and it pushed the key out, the bearing broke though, but that's fine, since I'm replacing it.
Here is a video and some pictures:
arbor3.jpgarbor2.jpgarbor1.jpg
-
10th May 2024, 11:25 AM #7SENIOR MEMBER
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 649
Good one you sure you got the right guy on linked in? Didn't see the request.
I did consider a VFD but the one I looked at was a bit more than a new motor and wasn't confident in setting up a VFD myself (& wasn't keen to spend the $$$ on a sparky to do it for me) - I believe they are pretty straight forward mind you, as long as you have the motor plate with all the details you just have to put in the motor specifics. There are some really cool options too like slow start up and motor braking at shutdown etc.
Where it all got a bit fuzzy for me was the Delta vs Star motor considerations BUT perhaps new VFDs get around this automatically and it doesn't mater so much?
The other consideration was the lose of power via a VFD (not sure if this is still the case), was told to expect a lose of ¼ of the HP of the motor using a VFD. Probably not that big a deal if you have a 3HP motor mind you.
Similar Threads
-
VFD for my vintage AEI 3 phase motor (running a Dyco Superfine 12" table saw)
By campidelli in forum ELECTRONICSReplies: 5Last Post: 7th May 2024, 08:06 PM -
Dyco 12" Table Saw
By Charlie_6ft in forum ANTIQUE AND VINTAGE MACHINERYReplies: 11Last Post: 6th May 2024, 06:11 PM -
Masport/Dyco tablesaw 12"
By Hanilein in forum TABLE SAWS & COMBINATIONSReplies: 4Last Post: 8th January 2022, 03:44 PM -
Dyco Superfine 305mm Table Saw
By GeoffreyEdwards in forum WOODWORK - GENERALReplies: 2Last Post: 8th February 2021, 09:57 PM -
Dyco "woodworker" 5 in 1 machine
By Dion N in forum HAND TOOLS - POWEREDReplies: 9Last Post: 20th August 2004, 02:51 PM