Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 20 of 20
Thread: Wadkin RB Stand Type Buzzer
-
23rd August 2020, 05:00 PM #16
Cutterblock Completion - pt.1.
After a lot of searching I found the spacer (and the one for my other RB) and the nut - but couldn't find the key anywhere.
RB 555.jpg Newer RB pulley, spacer and nut (top), older RB gear and spacer (bottom).
So I used the tried and true, proven, Murphy's Law method - and bought a short length of 5/16" key steel - which means the old key suddenly appeared .
RB 556.jpg
A trial fit of the spacer and key.
RB 557.jpg
Then full assembly.
RB 558.jpg RB 559.jpg
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
23rd August 2020 05:00 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
23rd August 2020, 05:39 PM #17
Cutterblock Completion - pt.2.
I found those spacers in the box that stores the knives. I decided to fit the original knives for now.
I didn't know about balancing the studs and nuts to within 0.2g until I started my RB projects (my Makita thicknesser uses disposable knives that never need weighing). But even I knew that resharpenable knives are always balanced.
Well nearly always... apparently . One knife weighed 176.1g, but the other weighed 177.4g . A bit of careful grinding - I took a bit off each end of the heavier one (top) 'til I got it down to the same weight.
RB 562.jpg RB 563.jpg Genuine Wadkin knives .
Then on to the cutterblock, adjust to approximate position, fit the 'clamshells', and slightly tighten.
RB 561.jpg
RB 560.jpg
Final knife setting will come later. I'm intending 80ft/lbs torque on the nuts ('though I have heard higher).
Next steps will be reassembling the motor (which is not original to this machine) and some work on the electrics, as every bit of original electrical equipment was stripped from the buzzer by a previous owner - I would guess as a step toward conversion to single phase.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
26th August 2020, 10:27 AM #18SENIOR MEMBER
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 678
Awesome work Vann - a shelix cutterhead in one of these would go awesome but thats just me dreaming!
-
28th August 2020, 01:40 PM #19
Motor - pt.1.
My original plan was to fit either this 2.5hp Brooks motor...
RB 513.jpg
...or this 2hp Crompton-Parkinson motor.
RB 514.jpg
But both were 1400rpm motors, while the original ran at 2800rpm. I could still use one, but would need a much larger drive pulley to get the cutterblock running at the required speed. Both would also need adaptor plates to fit the RB motor shelf.
And I still had the motor off this rusted Wadkin CK radial arm saw.
RB 504.jpg
I suspected it would be munted, but a megger test said it was still okay. And it's 2hp 2800rpm. So I took it to bits, cleaned it up, cleaned out and regreased the bearings, and repainted the case. I also made up an adaptor plate out of a piece of scrap (not quite wide enough - but near enough.
Yesterday I trial fitted the adaptor plate to the motor case, and this morning I cut off the protruding shaft.
RB 565.jpg RB 566.jpg
RB 567.jpg The other large hole was already in the plate when I got it.
The three screws in the adaptor plate pick-up existing holes in the motor case. The forth screw hole is blocked by an original broken off screw. I think I'll drill and tap two or three more holes for two or three additional screws (although it feels quite firm as is).
Next I need to position the motor in roughly the correct position on the motor shelf to refine the adaptor plate. To do this I needed to reassemble the motor. I fitted the end bell (and forgot to take any photos as it was being assembled).
RB 564.jpg
Then fitted the rotor and bell to the case (without the stator at this point).
RB 568.jpg The heater is to warm the case so the ball bearing race sides in easily.
And a trial fitting.
RB 569.jpg The vee belt is off my compressor - and is far too long.
The adaptor plate needs shortening and I'm sure there'll be several more mods before it's ready for final fitting. But, small steps...
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
6th September 2020, 02:16 PM #20
Was Ist Das?
And that's near my total German vocabulary .
RB 570.jpg
It's for a change in plans. I was going to use these 1974 On/Off switches, as the screw holes are still in the same location as the original RB On/Off switches of ~28 years earlier...
...but some of the contacts are very close to the cast iron surrounding the opening. I really don't want to risk a 400v short circuit when switching on the machine .
Another complication is the switchgear...
...which appears to be suitable, and in good condition - but I've decided to pass it on to another Wadkin CK owner who has modern switchgear on his and would like something more original.
So now the plan is to fit this MEM Series #4 DOL starter, to that weird thing (bracket) in the first photo...
RB 571.jpg
...and attach it to the machine stand using the On/Off switch plate holes.
RB 572.jpg Trial fitting.
So why does the bracket stick up above the DOL starter? Well it's because I've never set up a buzzer cutterblock before and I'm very nervous about starting it for the first time (you know, flying knives and other possible things that could go wrong). So for the first few start-ups I'm going to use this VFD (which I bought for my Wadkin LP recessor - which is also 2hp).
RB 573a.jpg Trial fitting.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
Similar Threads
-
Wadkin RB Bench Type Buzzer - RB 116
By Vann in forum ANTIQUE AND VINTAGE MACHINERYReplies: 89Last Post: 18th March 2024, 10:06 PM -
Wadkin RB Buzzer
By Vann in forum ANTIQUE AND VINTAGE MACHINERYReplies: 124Last Post: 27th January 2022, 02:13 PM -
Wadkin Buzzer/Jointer for sale in Tas
By jrock_au in forum ANTIQUE AND VINTAGE MACHINERYReplies: 2Last Post: 25th October 2019, 12:59 PM -
Wadkin FTD setting stand
By jgforsberg in forum ANTIQUE AND VINTAGE MACHINERYReplies: 1Last Post: 5th February 2018, 01:57 AM -
Make an offer ?? Wadkin RC Buzzer
By auscab in forum ANTIQUE AND VINTAGE MACHINERYReplies: 7Last Post: 29th June 2017, 10:31 PM