Thanks: 0
Needs Pictures: 0
Results 1 to 10 of 10
Thread: Wadkin rs questions
-
16th September 2017, 10:47 PM #1
Wadkin rs questions
I have just acquired a 1953 RS lathe. Was difficult to move but managed and it it is place.
I have swapped out the 1ph motor to a 3ph motor with variable speed control.
Should have been running today but was supplied the wrong inverter so have to wait until next week to get the replacement.
Questions:
Is there a source for a 1 3/8 x 6 tap to suit the headstock spindle ?
Is the only difference between the 6", 8" and 10" the length of the leg ?
If so is it possible to shorten the leg on a 6" to make it a 8" ?
Thanks
Phil
-
16th September 2017 10:47 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th September 2017, 11:00 AM #2
Photos please (including one of the Wadkin tag).
Originally Posted by Phil Hansen
Of course Wadkin machines were hand fitted - so if you put a bed off another RS onto your headstock, the locating pins won't align. You'll need to drill new pin holes - or rely solely on the bolts.
But that's not quite what you are asking. I believe most RS legs are cast, but some are fabricated. Shortening a fabricated one should be easy enough. Shortening a cast one... I think it would be easier to make a new one out of angle iron. My 6" RT has cast legs (plural).
As for the 1 3/8" x 6 tap - I haven't looked for one. A good turner would be able to cut an internal thread if you get desperate.
HTH.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
17th September 2017, 08:21 PM #3
Thanks Vann,
Will give the conversion a miss.
Have already submitted the tag picture but here are a few more.
I swapped out the 1ph motor for a 3ph and fitted an inverter. Remote start and speed control box can be put anywhere. It has a magnetic back.
The panel on the front had a digital tacho and switches for lights as well as an emergency stop.
Haven't run it yet as the supplier gave me the wrong inverter. Should get the correct one on Tuesday.
Cheers
-
18th September 2017, 12:24 AM #4SENIOR MEMBER
- Join Date
- Sep 2012
- Location
- uk
- Posts
- 456
Hi Phill so have you done away with the stepped pulley and just rely on the inverter for differing speeds. I suppose you could increase the capacity by putting something in between the tailstock and the bed. I've got the 10" and its just a casting.
Looking at your tag it states 3 phase I wonder where the single phase motor was done because it is a proper RS motor.
Do you know of any good machinists who could make an adapter, I got mine from peter child but like you said he is no more.
Vann, I got told off the old dealer guy that I visit that the RT was an apprentice lathe to prepare youngsters for the RS and RU
-
18th September 2017, 02:05 AM #5
Hi Wallace,
I got the lathe with a huge 1ph motor - must have been a replacement to suit the previous owner . I had a 3ph motor and inverter which I bought for a project that never got going.
So I cut off a bit of the long original shaft and made an adapter with key ways and locks to bring it back to original length.
So the original stepped pulley is still in place. Went that way as trying to replace the headstock pulley would be a mission.
Another consideration would be how to replace a belt if you did not have a spliced belt.
Have done drawings (my sketches) of what I need for adapters and will talk to them this week.
Cheers
-
18th September 2017, 02:13 AM #6
-
23rd September 2017, 08:14 AM #7SENIOR MEMBER
- Join Date
- Oct 2009
- Location
- South Africa
- Posts
- 950
-
23rd September 2017, 07:39 PM #8
-
24th September 2017, 04:50 AM #9SENIOR MEMBER
- Join Date
- Oct 2009
- Location
- South Africa
- Posts
- 950
No, I haven’t seen any of it. I chatted to him at one of the guild meetings, so I knew he was planning to sell the lathe, but he couldn’t remember the make at that stage. I was away in the Cape when the email saying what was for sale, and by the time I’d got home and done a little research on the lathe, you’d already taken it.
To be honest, I was a little relieved when I found out it had been sold, because I’ve spent my toy allowance for the entire year, but would have found the money somewhere for something like that - I’m not likely to see another one for sale in a long time.
Just out of curiosity, what size is the Wilson bandsaw?
-
24th September 2017, 06:34 PM #10
Similar Threads
-
Wadkin LPD
By wallace1973 in forum ANTIQUE AND VINTAGE MACHINERYReplies: 6Last Post: 23rd December 2017, 08:58 PM -
Wadkin PK - Can I fit a Single Phase Motor to a wadkin pk table saw?
By Pommy Ker in forum ANTIQUE AND VINTAGE MACHINERYReplies: 17Last Post: 30th December 2015, 06:31 PM -
Wadkin PK manual link and other wadkin manuals
By Pommy Ker in forum ANTIQUE AND VINTAGE MACHINERYReplies: 0Last Post: 29th December 2015, 07:56 PM -
A wadkin PK for Me
By auscab in forum ANTIQUE AND COLLECTABLE TOOLSReplies: 22Last Post: 8th July 2014, 09:27 AM -
Wadkin RAS
By pmcgee in forum ANTIQUE AND COLLECTABLE TOOLSReplies: 1Last Post: 5th October 2012, 09:52 PM