Thanks: 0
Needs Pictures: 0
Results 1 to 15 of 18
Thread: Tanner 300mm Thicknesser Manual
-
19th January 2017, 08:46 AM #1New Member
- Join Date
- Jan 2017
- Location
- East London South Africa
- Age
- 55
- Posts
- 1
Tanner 300mm Thicknesser Manual
Hi
Does anyone have a Manual for a Tanner 300mm Thicknesser Circa 1950.
Kind Regards
Machiel
-
19th January 2017 08:46 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
6th December 2017, 07:14 PM #2New Member
- Join Date
- Jun 2013
- Location
- North Shore, Waitamata Harbour.
- Posts
- 6
Did you have any luck? I'm looking for one too but unfortunately manuals tend to get binned.
-
31st January 2018, 12:31 AM #3New Member
- Join Date
- Mar 2013
- Location
- Adelaide , Australia
- Posts
- 3
Hi, Machiel, I do not have the manual but after many months ( mid 2016 )of emailing and phone calls around Australia and to New Zealand, where they were made, I was extremely lucky in getting some exploded diagrams of the Tanner 12 inch thicknesser.
Mine had come from a cattle station and I intend to rebuild it. I am sure it must have had a heavy life. I have just sighted your thread 30/01/18
Regards,
Alan
-
31st January 2018, 12:40 AM #4New Member
- Join Date
- Mar 2013
- Location
- Adelaide , Australia
- Posts
- 3
Hi, Go Fish !, Sheer luck I saw your request. Have not looked at this forum for long over a year. Bought 12 inch Tanner thicknesser ( 2016 ) which came from a cattle station. Intending to rebuild it after a heavy life. After months of chasing I have some exploded diagrams but no manual.
Regards,
Alan
-
17th February 2018, 10:05 AM #5New Member
- Join Date
- Jun 2013
- Location
- North Shore, Waitamata Harbour.
- Posts
- 6
Hello Alan,
I'd love a copy if possible. I'm helping a friend who has bought one, converting from 3~ to 1~ plus repairing some damage so any info at all would be appreciated. It will be moving up to the West Coast South island when done so it would be nice to get it 100% and pictures speak loudly.
I'm sure there are others who would like as well, any chance you could scan and post?
-
2nd December 2018, 02:56 AM #6New Member
- Join Date
- Dec 2018
- Location
- zim
- Posts
- 1
Hello,
Sorry to resurect this thread but I'm also looking for any literature about this machine?
Thanks
-
4th January 2019, 10:10 PM #7New Member
- Join Date
- Dec 2015
- Location
- South africa
- Posts
- 1
Tanner Thcknesser - diagrams
Hi Alan,
I note the thread is very old, however, have not been able to find anything more recent that is of any use. I inherited an old 300mm Tanner Thicknesser from my late Dad. it is missing a few V-belt pulleys and the motor so i am a little lost on what should be installed to ensure the correct output speed.
would you possibly still have those diagrams handy that you spoke of?
Kind Regards
Greg
-
22nd January 2019, 06:14 PM #8New Member
- Join Date
- Jan 2019
- Location
- Curra Qld
- Age
- 75
- Posts
- 4
Hi Beasponge. Did you have any luck with the manual for the Tanner thicknesser. I too am chasing info like pulley sizes etc. cheers. Pete
-
15th February 2019, 05:24 PM #9New Member
- Join Date
- Jan 2019
- Location
- Curra Qld
- Age
- 75
- Posts
- 4
Hi Greg. Do you have any photos of the spur gear pinion pulley set up etc on your machine. Cheers. Waggie36
-
18th August 2019, 11:09 PM #10New Member
- Join Date
- Jan 2019
- Location
- Canberra
- Posts
- 1
Hi guys, I'm a bit late to the party, but is that exploded diagram available still, and also did you guys figure out your pulley ratios? I've just picked up a tanner that is intact and could provide measurements if still needed.
Thanks,
Bonobo
-
26th April 2020, 09:01 PM #11New Members
- Join Date
- Apr 2020
- Location
- Geelong
- Posts
- 1
I am trying to set up my Tanner thicknesser.
I have cleaned up the in feed roller. I do not know if the bronze casting behind the infeed roller has to be able to travel above the roller or not. Is there a spec for this.
What size should the blades be, Mine as some 3 mm spaces below them to raise them.
-
19th May 2020, 10:51 AM #12New Member
- Join Date
- Apr 2012
- Location
- melbourne
- Posts
- 1
hi
im on the hunt for a manual for a tanner 12' thicknesser
any leads
-
22nd February 2021, 08:20 AM #13New Members
- Join Date
- Feb 2021
- Location
- Tumbulgum nsw
- Posts
- 1
Hi, I'm new to this forum (any forum for that matter) I have got a 12" Tanner thicknesser & it came with some instructions. I just have to work out how to up load them.
Tanner Thicknesser instructions.pdf
-
12th January 2022, 01:50 PM #14Gatherer of rusty
planestools...
Proud member of the Wadkin Blockhead Club .
-
29th July 2022, 08:09 AM #15Novice
- Join Date
- Mar 2010
- Location
- New Zealand
- Posts
- 20
Similar Threads
-
Tanner 6" Jointer Manual
By anthonyz in forum GENERAL & SMALL MACHINERYReplies: 1Last Post: 30th November 2021, 08:05 PM -
Tanner Thicknesser
By Ian T in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 2Last Post: 29th March 2016, 09:21 PM -
Tanner thicknesser
By rev in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 2Last Post: 25th September 2003, 12:33 AM