Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 8 of 8

Thread: gun regulator

  1. #1
    Join Date
    Jan 2009
    Location
    Colorado Springs, CO USA
    Posts
    97

    Default gun regulator

    I have a husky spray gun regulator. I used it with lacquer. It got a smudge or some kind of damage to the lens. I used acetone to clean it off. Instead it damaged the entire lens. it's has a rough and blurry feel.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    4,464

    Default

    Acetone has melted the surface. Use car polish with fine abrasives or even toothpaste with abrasives to polish the plastic lense.

  4. #3
    Join Date
    Jan 2009
    Location
    Colorado Springs, CO USA
    Posts
    97

    Default Thank you

    Quote Originally Posted by Lappa View Post
    Acetone has melted the surface. Use car polish with fine abrasives or even toothpaste with abrasives to polish the plastic lense.
    I have used some plastic polish that is many years old. I don't see much change yet. I thought about what you thought about so I'll keep working on it.

  5. #4
    Join Date
    Apr 2014
    Location
    Little River
    Age
    77
    Posts
    1,205

    Default

    Before you start polishing you need to remove the original damage with progressively finer wet and dry sandpaper. Once there is no visible damage then you can start polishing but not with a power tool as the area is so small that you will rapidly melt the plastic.

  6. #5
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    Quote Originally Posted by Bohdan View Post
    Before you start polishing you need to remove the original damage with progressively finer wet and dry sandpaper. Once there is no visible damage then you can start polishing but not with a power tool as the area is so small that you will rapidly melt the plastic.
    Thanks for this. All mine have the same damage and I’ve been wondering what to do with them.
    Cheers
    Arron
    Apologies for unnoticed autocomplete errors.

  7. #6
    Join Date
    Jan 2009
    Location
    Colorado Springs, CO USA
    Posts
    97

    Default

    Very helpful. I wondered about this too.

  8. #7
    Join Date
    Nov 2008
    Location
    Canterbury UK
    Age
    67
    Posts
    3,994

    Default

    As described use something like wet and dry to get as smooth finish on the lens as possible before using something like burnishing cream which you can use a dremel type machine with a small buffing wheel but only apply gentle pressuse and keep removing from the surface to prevent over heating the lens. As stated above to mush pressure can overheat and melt the plastic

  9. #8
    Join Date
    Jan 2009
    Location
    Perth, Western Australia.
    Posts
    68

    Default

    Go to a welding products supplier or eBay and seek out a polycarbonate clear welding lens or safety lens replacement. They come in a hundred different shapes and sizes.
    Pick out a flat piece of heavy polycarbonate lens replacement that has a bigger diameter than your gauge. I prefer at least 1.2mm thick. They can come up to 2mm thick in polycarbonate safety lenses for impact protection.
    Prise off the gauge lens retaining cover, it's usually only held on by a couple of dimples, or sometimes they're a twist lock. The premium gauges have the retaining cover held on by a couple of small screws.

    Take the old gauge lens out and lay it on the new replacement polycarbonate lens. Mark the diameter and cut a section out of the new lens to match the gauge lens.
    You can cut it to approximate dimensions with very sharp shears, a Stanley trimmer, tinsnips, or even Mothers kitchen poultry shears (provided she's not looking).

    Once cut out, trim to size and perfect circularity and gauge fit, using a small bench grinder, or a belt sander. Fit to gauge, refit retaining cover, and hey presto, you have a perfectly clear new gauge lens.
    Warning - don't touch the needle or try to clean gauge faces when the gauge is apart, they are both extremely fragile, and sometimes even just a gauge face wipe will remove numbers. Just blow any dust out with a gentle snort of air.

Similar Threads

  1. Samson air regulator
    By Matt_M in forum GENERAL & SMALL MACHINERY
    Replies: 2
    Last Post: 27th October 2015, 04:58 PM
  2. Regulator for Mig Gas ???
    By Stewart69 in forum WELDING
    Replies: 5
    Last Post: 4th June 2010, 03:31 AM
  3. Gas Cooktop regulator?
    By Spelunx in forum KITCHENS
    Replies: 5
    Last Post: 12th February 2007, 07:10 PM
  4. Regulator for LPG gas cooktop??
    By Pulpo in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 8
    Last Post: 3rd February 2006, 10:15 AM
  5. How do I set the regulator for my finishing gun
    By barrysumpter in forum HAND TOOLS - POWERED
    Replies: 7
    Last Post: 6th September 2004, 08:25 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •