Needs Pictures: 0
Results 31 to 45 of 85
Thread: Challenge 2020-21 Aussiephil
-
17th September 2020, 09:56 PM #31
-
17th September 2020 09:56 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th September 2020, 10:04 PM #32
Funny, I saw a cactus D
Sent from my SM-G950F using Tapatalk
-
18th September 2020, 08:56 AM #33SENIOR MEMBER
- Join Date
- Dec 2013
- Location
- Mt Waverley Vic 3149
- Age
- 81
- Posts
- 679
Definitely a woman with long gown and flowing sleeves. Her head is bent backwards while she washes her hair. Can't see head because photographer took the shot from too low an angle.
Bob
-
18th September 2020, 08:24 PM #34SENIOR MEMBER
- Join Date
- Aug 2006
- Location
- Canberra - West Belco
- Age
- 63
- Posts
- 646
Well after work i thought i would try and mill a blade up for the little model
Had some 50x5 that i cut a section out and went to practice on the mill
I actually got all the tapers on and got to what seems really close. milled a 25 deg bevel, run it over some 600 wet/dry to get it vague sharp... actually it's sharper than all my kitchen knives atm It is not hardened btw.
Hammered it in like you do for a normal Kanna, set the skew by feel and grabbed a bit of 42x19.
a couple of bevel passes and i was confident to try it on the 19mm side and got this.
_M182741.jpg
Actual real curvy bits coming out
I had some hardwood sections so thought, what happens if i try and bevel the edges.
Sheesh that worked as well.... the big curly bit is pine but the small stuff still in the mouth is from the hardwood
_M182745.jpg
Feeling pretty chuffed right at the moment
-
18th September 2020, 08:46 PM #35
-
18th September 2020, 09:47 PM #36
Phil
You need a T-shirt:
"Plastic Fantastic."
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
18th September 2020, 10:53 PM #37SENIOR MEMBER
- Join Date
- Aug 2006
- Location
- Canberra - West Belco
- Age
- 63
- Posts
- 646
Thanks Matt, i was having some trouble believing it worked as well....
Note to judges: this is firmly in the Proof of Concept part of the build and not a formal entry... but if there are bonus points for creativity and getting into the spirit of the puns for the last week then i won't say no
Paul: mmmm i have an account with a custom t-shirt place
A couple more photo's of the blade, it was a mix of use the DRO and angle gauges and just eyeball it it will be close measuring.
The good camera doesn't hide the tooling marks that's for sure.
Sitting on the cutting mat it's easy to see the top to bottom taper, its a bit harder to pick out the 3deg taper on the body above the blade bevel. Might redo this for some practice.
_M182750.jpg_M182747.jpg
-
18th September 2020, 11:09 PM #38
-
18th September 2020, 11:51 PM #39SENIOR MEMBER
- Join Date
- Aug 2006
- Location
- Canberra - West Belco
- Age
- 63
- Posts
- 646
Nah I wish, it was just a section cut out of basic 40x5 flat bar from bunnings that I had lying around. Being low carbon I won’t be able to harden it either but it’s good for practice on machining the blade shape.
‘the bit of bar I have is cupped bad enough that by the time I flatten both sides it’s under 4mm thick. At least now I think I’ve got the milling order sorted with respect to holding it in the vice
cheers
Phil
-
19th September 2020, 08:40 AM #40SENIOR MEMBER
- Join Date
- Dec 2013
- Location
- Mt Waverley Vic 3149
- Age
- 81
- Posts
- 679
Most impressive Phil. First completed plane that has been posted - congratulations
Cheers
Bob
-
19th September 2020, 12:14 PM #41
Definately better than this one
Import Tool Madness: PLASTIC hand plane. ($3.80; free shipping) - YouTube
You should get that design protected asap!
I wouldn't be surprised if it doesn't show up on one of these cheap shopping sites......
Sent from my SM-G950F using Tapatalk
-
19th September 2020, 07:34 PM #42SENIOR MEMBER
- Join Date
- Aug 2006
- Location
- Canberra - West Belco
- Age
- 63
- Posts
- 646
Well it might have been done as a bit of humor to fit in with all the plane puns and a small proof of concept but I spent quite a bit of time today ripping some of my floor boards to make some French cleats and then started sanding the edges to break sharp edges and thought “what am I doing this the hard way” and reached for this little plane. Even with the unhardened blade it work fine to give a small bevel that only then took a couple of swipes with some 240 to finish
My confidence is now high I can pull off a full size version
-
1st November 2020, 07:12 PM #43SENIOR MEMBER
- Join Date
- Aug 2006
- Location
- Canberra - West Belco
- Age
- 63
- Posts
- 646
Finally a small bit of momentum again, son dropped off a leaf spring that will yield a few blades.
PB010835.jpg
There is at least a 100mm section each side of the centre hole that appears relatively flat as a starting point
PB010836.jpg
I didn't grab a photo of the measurement not counting the radius but it was close to 70mm so that is near spot on design goals.
It is 13mm thick though so i either design for the thickness or take some time on the mill to get down to 10... my first thought is a nice heavy blade will be good.
-
1st November 2020, 08:23 PM #44
Phil
I enlarged the pix to get a good look at your leaf spring. It looks good and with your milling machine you will be able to get an excellent surface after annealing and flattening. It will be interested to see how the thick blade goes as I have the same thing.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
1st November 2020, 08:35 PM #45
We should almost have a sub category for planes originating from car Junk.
Good to see some action Phil !
13 mm thick plane iron wow,
Well at least you won’t need to use a sharping guide to sharpen that bevel, if you use a full flat bevel.
Cheers Matt.
Similar Threads
-
Challenge 2020 - 2021 Simplicity
By Simplicity in forum PLANE CHALLENGE 2020-21Replies: 476Last Post: 1st January 2022, 11:20 PM -
Challenge 2020 - 2021 Oldgreybeard
By Oldgreybeard in forum PLANE CHALLENGE 2020-21Replies: 161Last Post: 2nd June 2021, 03:01 PM