Thread: Lights in Decking

Depends on whether you can access the underside of the deck after the boards are laid. If you can access the underside, finish the deck, then work out where you want the lights and wire them up.

If you can't access it, you'd have to do it as you went along.

In saying that, if you cant access beneath the deck after its built, you should probably use decking screws (not nails) so that you can lift the boards up for maintenance etc.

Trav

Hey,
Im actually laying deckboards as we speak...I have ordered lights, LED deck lights, they come in packs of 10 and are about 90 bux a pack.
They dont have any stock at the moment, which sux for me, but I know where the lights are going and Im putting in some speaker wire on the floor where its going.

Once I get the lights, all i will do is cut the hole witha hole saw, and use a coat hanger to pull up the speaker wire and use it to pull through the cables.

The only issue I have with the LED lights is that they plug into a power point, I wanted them to be wired into a light switch. Not a big deal as I have 2 outdoor powerpoints on my deck and I'll just run the extension cable up to that point.

Here are the lights im getting

Edit: Oh and Im screwing my boards down so if I have to remove a few its not a big deal.
Cheers.

Did you have a look at the HPM 12V deck light range... Simple as to connect you just drag around there heavy duty speaker cable and clip on the lights put a transformer on the other end and you in business ....
You can always use a yellow tongue strip to get from light to light if you get stuck fishing the cables through... The cable would be easy to get now so you could lay it now and get the lights later and cut your holes etc...We often run the cable under low decks for owners to deal with later

cheers utemad

when using decking lights, how do you install them without weekening the decking board?

You should try and put the light as close as possible to the joist, being careful not to put it too close to the nail/screw as it may split the board. I have 140mm wide boards and the hole to cut is 25mm so there is no real issue in my boards, when using 90mm boards you could put the light inbetween boards and have a semicircle cut from each board. It would still look pretty nice.

A tip for anyone having additional external power points placed outside to run water features and garden lighting is have the power point switched from inside the house as well. I use to have this done for many clients and it makes switching on water features and lights very convenient but keeps the simplicity of being able to plug in transformers and pumps.

On my new house I put two double external power points under my deck, one of them has each outlet switched from inside for when I set up my pond and lights.

Originally Posted by Burnsy

A tip for anyone having additional external power points placed outside to run water features and garden lighting is have the power point switched from inside the house as well. I use to have this done for many clients and it makes switching on water features and lights very convenient but keeps the simplicity of being able to plug in transformers and pumps.

On my new house I put two double external power points under my deck, one of them has each outlet switched from inside for when I set up my pond and lights.

Now that is a great idea! I need to get some lights done in my deck once it all is finished. So, you installed a couple of external power-points, but then had the switches put inside? Do you have switches on the powerpoints as well? How much extra did the switch inside cost?

Originally Posted by Spelunx

Now that is a great idea! I need to get some lights done in my deck once it all is finished. So, you installed a couple of external power-points, but then had the switches put inside? Do you have switches on the powerpoints as well? How much extra did the switch inside cost?

The power point still has switches, just use regular external power points, these points however are in turn switched via internal light switches. For the power point to be live, both switches must be on. Not being a sparky I am not sure of the exact process.

Price will always depend on how much work is involved, if your powerpoint is on an external cavity wall and the switch is just above it inside then price difference is not huge. I use to do this wherever possible as clients don't like digging around behind some shrubs in the dark trying to find the external power point to turn their garden lights on.

Ok so here is my dilema. I have bought 2 kits, which require to power points. I only have 2 power points outside, and Its too late for me to get a switch wired up inside, the house is already built and the points are no where near a light switch...

Surley putting a power board under the deck and running an extension cable to the power point is not safe...

Any ideas?

Its too late for me to get a switch wired up inside

Why is it too late? It's never too late for a sparky with the right gear.

You know what, You're right Silent, I just had a brilliant Idea on where i could put another outside point that could hook up easily to my light switch inside....
Im gettin a little excitable.

If it's a power point, then it has to go on a power circuit. It's heavier cabling than a light circuit.
If there's sub-floor access, then the sparky will be able to hook into an existing power point, so long as the circuit can handle it. And as silent said, if he's got the right gear, and it's a cavity, or stud wall, then he could put a switch anywhere. If it's a single brick wall that you want to put it in, then you'd have to remove an architrave, or chase the wall and patch it up again.

If it's just hardwired lights though, then it could go on a light circuit from an existing switch, and he could replace it with a double switch.

The Lights I have bought (found none different) plug into a power point....Could not find any that are wired like downlights for example..not that you'd want them in ur decking.

Althought I haven't done this to a deck yet...... I did apply this principal to my pool.

My pool lights (internal underwater 24v ) are wired to a meter/power box at the side of the pool. The power box contains the 24v transformers, I told my sparkie that I wanted the pool lights to go on and off automaticly with a timer, but too also have an override switch inside the house so that I can put the lights on when I have a party... or want to light up the pool after the timer has gone off.

I had the same thing applied to 2 massive flood lights that I use to light up two 100ft gum trees. ( no timer on the flood lights )
the same principal can be used for decking or garden lights. .......

..... so one step further....... ask your sparkie in install a timer..... they were $20 extra.... and worth every cent.