Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 6 of 6
  1. #1
    Join Date
    Dec 2007
    Location
    Adelaide
    Posts
    62

    Default Repair or patch cracks in internal walls

    Can this type of wall cracking be "repaired" or is patching the only thing that can be done? If it can be repaired how is it best done ? I've got a copy of the CSIRO brochure which describes the repair procedure recommended by them, but most customers freak out at the cost of the CSIRO procedure. I usually do the following:
    Chip out all the loose stuff and the plaster that is no longer adhering to the bricks, once I start the loose stuff can usually be pulled off with the fingers. Often a 3mm crack ends up 120mm-150mm wide

    Hammer gavlanised metal strips about 1.5mm-2.00 mm thick into the brick gaps to stop the gap from closing up in future. The theory is that if the crack closes up the patching gets pushed out of the crack causing the wall to bulge at that point. I do this about every 120mm-150mm all the way down the crack.

    Apply bonding agent to the bricks, then trowel motar into the crack almost level with the existing good plaster. Usually have to use a scraper here to apply the motar as a trowel is too wide.

    Plaster over this with cornice cement/patching plaster.

    Finich off with skim coat flushing compound which may need a light sand when dry to make truly flush.

    All this is very time consuming is there a better faster and or better way?

    I was replacing some cracked tiles in a shower alcove and I watched the painters for a while, a quick scrape with a scraper, fill the crack with super fine plaster, a quick sand when its set then on with the paint.

    Am I being too fussy? Seems to me there must be a quicker better way. Some times I find fibeglass tape from a previous repair (the type used for gyprock) under a crack, as its torn in two I have to pull it away which makes even more mess.

    Is this type patching better?

    There's been a few very dry years in SA which has caused a lot of cracking even in previously stable houses, most people don't want to know about soil engineers and reports they just the cosmetics taken care of


    Some advice would be appreciated
    Last edited by familyguy; 2nd May 2008 at 12:06 AM. Reason: Pics did not upload

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Jul 2006
    Location
    Melbourne
    Posts
    709

    Default

    This has worked for me for years.
    http://www.how2plaster.com/restlath.html

    Cheers Rod
    Great plastering tips at
    www.how2plaster.com

  4. #3
    Join Date
    Dec 2007
    Location
    Adelaide
    Posts
    62

    Default

    Thanks for the reply, I did read those but wasn't sure if it applied to brick walls also.

  5. #4
    Join Date
    Mar 2008
    Location
    Lambton, Newcastle, NSW, Australia
    Posts
    4,957

    Default

    Slipping the metal in before bogging up sounds like a good idea (metal or some timber wedges)
    Instagram: mark_aylward
    www.solidwoodfurniture.com.au


    A good edge takes a little sweat!!

  6. #5
    Join Date
    Nov 2006
    Location
    Melbourne
    Posts
    18

    Default

    Buy premixed mortar mix and follow the instructions on the pack. Add around 100ml to 200ml of bondcrete to the mixture. This will allow an extra strong bond. The bricks will need wetting before applying the mortar mix to stop the bricks from absorbing moisture from the mortar mix and will stop it from cracking. Use bondcrete again for the wetting agent and follow the instuctions on the container.
    One you apply the wetting agent, apply the mortar mix with a trowel starting from the top and finish at the bottom. Using a piece of timber level the mortar to the existing wall. Allow to dry for 24 hours then apply plaster top coat. Works a treat. good luck

  7. #6
    Join Date
    Aug 2003
    Location
    Conder, ACT
    Age
    77
    Posts
    6,051

    Default

    Plenty of bondcrete.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •