Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
4th June 2023, 09:27 AM #1GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,334
How to remove toilet outlet valve
Hi. I have a toilet which is slowly leaking water into the pan. I’m assuming it’s probably just a seal on the outlet (flush) valve that needs replacing. I can’t see how to remove this style of outlet valve and don’t want to use force. Can anyone tell me how it should be removed.
It’s a close coupled caroma but not sure if the outlet valve is original.
Cheers
Arron
0D05D1E3-211E-4739-B5F3-B98CFEF31989.jpgApologies for unnoticed autocomplete errors.
-
4th June 2023 09:27 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
4th June 2023, 10:23 AM #2
A lot of flush valves rotate and come out as an assembly of the seat like the link below
How to replace the seal on a top mount outlet valve in a Caroma dual flush toilet - YouTube
-
4th June 2023, 11:46 AM #3Member
- Join Date
- May 2023
- Location
- Maroochydore
- Age
- 76
- Posts
- 97
Yep as above, slight anti clockwise click and lift out
Mark L and R on top in case you manage to put it back opposite to what it came out which will change the flushes.
And make doubly sure the new washer is fully seated or it will never stop leaking.
Washers readily available from local plumbers supplies, no, not bunnings, they only sell overpriced replacement washer kits that usually don't suit.
And once it is back in make sure the inlet valve is shutting off not overfilling and running out the centre overflow.
-
4th June 2023, 01:26 PM #4GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,334
Another question
Thanks guys. With the confidence of knowing I was doing the right thing I was able to get it out fairly quickly. The odd thing is that there are a couple of little raised lumps on the seal. You can see them in the photo. There is nothing on the mating surface that they could relate too. Should they be there ?
Cheers
Arron
547052C6-5260-496B-9223-5FE599DEE4EB.jpgApologies for unnoticed autocomplete errors.
-
4th June 2023, 01:56 PM #5Member
- Join Date
- May 2023
- Location
- Maroochydore
- Age
- 76
- Posts
- 97
Had one like that last week had air bubbles in it from delamination
Might be same problem.
Otherwise no idea.
-
4th June 2023, 05:52 PM #6GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,334
YEp, poked a pin in them and they deflated completely. Oddly they were full of fluid, not air, but obviously just delaminating occurring.
Thanks
ArronApologies for unnoticed autocomplete errors.
-
5th June 2023, 04:37 PM #7Senior Member
- Join Date
- Mar 2008
- Location
- Cairns
- Posts
- 192
-
5th June 2023, 06:36 PM #8Member
- Join Date
- May 2023
- Location
- Maroochydore
- Age
- 76
- Posts
- 97
LOL yea makes sense to have water not air as the flush washer is under water all the time.
TBH I took one quick look at the bubbles and dropped the washer in the bin.
Didn't even think when typing just quickly somehow assumed air bubbles.
Must be getting old or spending too much time in the beer garden or both.
Similar Threads
-
Other uses for Valve ResurfacerAny Other Uses for Valve Resurfacer??
By MWF FEED in forum ANTIQUE AND VINTAGE MACHINERYReplies: 0Last Post: 26th May 2022, 10:50 AM -
15A power outlet
By Cin in forum GENERAL & SMALL MACHINERYReplies: 16Last Post: 26th October 2011, 09:21 PM