Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
9th August 2005, 10:16 AM #1
Senior Member
- Join Date
- Jan 2005
- Location
- Brisbane
- Age
- 52
- Posts
- 468
Removing a toilet..and then putting a new one in
Hi,
I am in the middle of the tiling the house...and need to rip out a tiolet, whilst I was at it I was going to put a new one in.
I am making a few assumptions....
1. How hard can it be!
2. The toilet is/will be screwed and siliconed to the floor.
3. Its an S Trap - that is 90mm from the wall - so this is the set out?
Has anyone got any advice on doing this properly, I'd also like to know about what to do in the actual trap area where the PVC coupling is.....
Regards
Warren
-
9th August 2005 10:16 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th August 2005, 02:12 PM #2
GOLD MEMBER
- Join Date
- Apr 2002
- Location
- Brisbane
- Posts
- 5,773
If this is your typical toilet pan, with the outlet thru the floor.
undo the 4 screws, knife the silicon and carefully prise the pan off the floor. the pipey bit at the back should just "unplug" from the pan collar. Unless it was installed in antiquity & the pan collar will be melted tar inside an earthenware pipe, in which case its a bugger.
Probably a good idea to plug up the hole with something till later.
insatllation is the reverse of the above. you may want to renew the seal and or the pan collar.
Don't get too keen on the hold down screws you don't want to crack the pan.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
9th August 2005, 09:38 PM #3
Deceased
- Join Date
- Feb 2005
- Location
- East Bentleigh, Melbourne, Vic
- Age
- 68
- Posts
- 4,494
Call for the plumber. Urgently!
Originally Posted by soundman
-
9th August 2005, 11:42 PM #4
Senior Member
- Join Date
- Nov 2004
- Location
- Melbourne
- Posts
- 108
Soundman is spot on...over tighten those screws...and bang...crack the pan...proceed with caution. Originally Posted by soundman
-
10th August 2005, 12:05 AM #5
Retired Marine Engineer
- Join Date
- May 2005
- Location
- Newcastle
- Age
- 72
- Posts
- 3,363
Make sure you have a new rubber joint to fit the new pan to the old pipework and to fit to the cisten .
Can be a bastard to sourse late sunday afternoon
Only use stainless screws bolts , don't be tempted to use steel
Check new pan and seat will fit to old cisten
Rgds
Russell
Useless infomation for the day
Man who run behind car get exhausted.
-
10th August 2005, 01:01 AM #6
Starter
- Join Date
- Mar 2005
- Location
- Too close to Sydney
- Posts
- 1,385
Your offset is very short if it is 90mm from the centre of the pipe to the wall. You can buy an offset collar which will give you a further 50mm if you need it. Measure from the wall to the centre of the pipe, that is your offset. Then find a toilet to suit.
Its easier to just buy a set that has a variable offset distance.
Dont bother buying seperate pan and cistern, individually they are about a much as a set.
-
10th August 2005, 11:22 AM #7
Feel a bit like Rocko
- Join Date
- Jun 2003
- Location
- Melbourne
- Posts
- 1,091
Having recently been faced with a similar project, I went with the plumber option.
This is only because I have finally found a reliable plumber. Been a six year journey that. If I have not had found a good plumber by now, I would have done it myself.
But all the discussed issues I am sure would have come up replacing the old bog.
