Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: 30 degree Segmented Bowl
-
20th April 2005, 07:03 AM #1
30 degree Segmented Bowl
Maple & Mahogany detail ring with Purpleheart. Top and bottom base is Bubinga. Birch and ebony stained walnut veneer for the seperators. It was an excuse to use my new disk sander and fancy miter gauge. 16 pieces for the normal rings and 32 for the detail ring.
finish was Oxford waterbased spray lacquer, many coats, buffed with wet Abralon pads to 4000, then Merzenna 16L buffing paste and then Carnuba.Last edited by Dr_Dewey; 20th April 2005 at 07:13 AM. Reason: i'm an idiot
-
20th April 2005 07:03 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th April 2005, 09:24 AM #2
Awesome...
"I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
20th April 2005, 09:54 AM #3
Yes - that absolutely unreal. The work to prepare the blank must have been huge - let alone the turning.
Well done.
CheersThe Numbat is a small striped marsupial whose whole diet consists of termites.
-
20th April 2005, 11:43 AM #4
Hell of a piece, very jealous.
Keep up the good work.
Matt.Quantum materiae materietur marmota monax si marmota monax materiam possit materiari?
-
20th April 2005, 11:55 AM #5
Bloody great work. Maybe you could post some details about your joining method as well as how long it took to do.
Cheers
KrisLast edited by Kris.Parker1; 20th April 2005 at 11:56 AM. Reason: Because I am a typing spastic!
"Last year I said I'd fix the squeak in the cupbaord door hinge... Right now I have nearly finished remodelling the whole damn kitchen!"
[email protected]
-
20th April 2005, 02:02 PM #6Originally Posted by silentC
-Ryan
there's no school like the old school.
-
20th April 2005, 02:41 PM #7
Oh, wow. Looks like something that should be in one of those displays in a palace somewhere.
The only way to get rid of a [Domino] temptation is to yield to it. Oscar Wilde
.....so go4it people!
-
20th April 2005, 09:02 PM #8
Absolutely Fantastic!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I can't wait to get a lathe, one hell of an inspiration.Have a nice day - Cheers
-
20th April 2005, 09:19 PM #9
-
20th April 2005, 09:38 PM #10
Wow! Looks like a lot of time and patients went into it, something I lack.
Love the shape and mix of timbers also, well done.Neil____________________________________________Every day presents an opportunity to learn something new
-
21st April 2005, 12:30 AM #11
How it was made
Many thanx for your kind words. it took several hours all told, but over a months time to figure how to do it right and build it up. The first detail ring was cut on a Dewalt SCMS for all the angles and it was a mess. I started with the maple and a strip of mahogany and laminated them and then cut 32 pieces at 30 degrees. try to get the bands equal thickness.
for a ring of 32 pieces the angle must be 5.625 so had to use a disk sander and a new miter gauge by Jessem that can be set to this angle, after some fine tuning. Cut 8 pieces from scrap and then try the angle and see if these eight will fit in a framing square (90 degrees) if there is a gap then adjust the angle in or out depending where the gap is, inside or on the outside of the pieces.
once the angle is right then sand each piece to the angle, then carefully glue them together, making sure the "V" matches and the faces are aligned, i did 5 at a time, and secured them with a rubber band while the glue set. then glued 2 together to make 10. with 3 ten piece arcs and 2 seperate pieces -finally assemble the ring and again check for gaps and fine tune the last 2 pieces. glue it all up.
mount it on jaws and clean up the edges so its at right angle to the bed.
now the final diameter can be measured and then build the rest of the rings, which are only 16 pieces or 11.25 degrees, using same method to check angles etc. With purpleheart, sanding can burn the wood and form black glue joints, so have to be careful, clean the sanding disk with crepe and light touches so as to no heat the wood.
made one mahogany ring and glued it on the rough bowl and and then parted it in half and then put the detail ring on and then the other half of the mahogany ring, then more veneer, parting rings saves a glue up!
the small bands of veneer were applied one at a time,
here is the final assembly ready to turn, some of the "V"s were a bit off.
regards
-
21st April 2005, 12:52 AM #12
Absolutely STUNNING!!!
-
21st April 2005, 02:59 PM #13
Thanks for the run down Doc! you're an inspiration!
-Ryan
there's no school like the old school.