Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 25 of 25
Thread: Stand for stereo system
-
8th December 2005, 04:37 AM #16Member
- Join Date
- Jul 2005
- Location
- Poole, Dorset, UK
- Age
- 65
- Posts
- 64
Very nice work, I bet you're well pleased.
From a fellow hi-fi nut.
-
8th December 2005 04:37 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
8th December 2005, 08:14 AM #17.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by daninjt
-
9th December 2005, 09:49 AM #18Originally Posted by daninjt
- The legs look like they are directly joined to the top without any kind of apron. Such a joint may be quite weak, even with M&Ts. What kind of joint did you use?
- The box containing the black unit that hangs underneath the top would have a lot of cross grain movement relative to the top it is joined to. Did you allow for this movement? How?
- The curved sides at the very top would suffer the same issue as (2).
- The slat sides on the middle two tiers would offer little strength against sideways racking. I can't see any bracing at the back, but putting some in would go along way to making the unit more durable in this regard.
- One of the things I like about the design is the overall lightness, but this leads to my concern that issues (1) and (4) mean that a sideways kick against one of the legs would severely test the integrity of the unit.
Those are my principles, and if you don't like them . . . well, I have others.
-
9th December 2005, 09:31 PM #19Member
- Join Date
- Mar 2004
- Location
- Montville
- Posts
- 83
Thanks Zenwood,
I was hoping for something I could learn from.
The legs are attached with biscuits and a couple of 7.5cm screws in each leg.
The thing at the bottom which holds the black power supply is just glued on. Any suggestions what to do if it falls off.
I am still planning to attach a back of some description to hide the wires but have not worked out what just yet.
As for the curved top, its just glued in place too. It was made in the garage which is hot and probably 70-80% humid. Now its in the A/c lounge which is 23 deg and 45% humid. I guess we'll see how it goes.
Cheers,
Dan
-
9th December 2005, 10:00 PM #20
Dan
I think the piece is an outstanding effort especially as Entertainment units of any kind are very hard to make look nice unless you hide everything away in a nice cabinet but your design is functional without being "in your face" Quite an achievement for someone just getting going in woodwork.
The piece could even do with a little more presence (pardon the audio pun) which could be achieved by the legs curving slightly outward front to back and side to side. It wouls just widen the stance and anchor it visually to the floor.
Well Done
RossRoss"All government in essence," says Emerson, "is tyranny." It matters not whether it is government by divine right or majority rule. In every instance its aim is the absolute subordination of the individual.
-
9th December 2005, 10:03 PM #21.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by daninjt
-
10th December 2005, 12:52 AM #22
The power supply box may be the most vulnerable component. A joint that allows movement would have been better for this: a sliding dovetail (tricky to cut) or buttons in a groove (like a tabletop), or special hardware (figure-8s etc.).
Putting a back on would help overall strength.
Would be difficult to modify any other elements of the design at this stage, but there's plenty of food for thought when you design the next one (maybe incorporating drawers for CDs).Those are my principles, and if you don't like them . . . well, I have others.
-
10th December 2005, 01:02 AM #23.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
It wouldnt be such an issue if it was full of Kenwood crap, but a few grand plus of high end gear in such a potentially unstable structure would have me prop up a car jack over night just to be sure
-
10th December 2005, 01:33 AM #24
As a quick insurance measure, maybe put two screws into each side of the power supply holder, say 20 mm and 100 mm from the back. Movement over the 80 mm won't be so much, and the screws will hold if the glue should catastrophically fail.
If you can find out what the wood is, some experts here should be able to calculate the amount of movement and tell you if the glue is likely to fail.Those are my principles, and if you don't like them . . . well, I have others.
-
11th December 2005, 02:43 PM #25Member
- Join Date
- Mar 2004
- Location
- Montville
- Posts
- 83
Thanks for the advice fellas. I'll take another look at the cross grained joints.
Cheers,
Dan
Similar Threads
-
Ez Smart Guide System?
By NewLou in forum HAND TOOLS - POWEREDReplies: 62Last Post: 9th May 2010, 10:49 PM -
Catchin the Rat........An Introduction to the Woodrat Joinery System
By NewLou in forum ROUTER JIGSReplies: 71Last Post: 11th April 2006, 09:24 AM -
Upgrading my 1hp DC system
By dai sensei in forum DUST EXTRACTIONReplies: 14Last Post: 18th June 2005, 11:46 PM -
Triton dust collection system
By STEPHEN MILLER in forum TRITON / GMCReplies: 1Last Post: 11th July 2000, 01:34 PM