Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 21 of 21
-
16th May 2024, 11:54 PM #16Senior Member
- Join Date
- Mar 2014
- Location
- Cowes, Australia
- Posts
- 209
Those final touches take so much time. Deburring the tig rods, inserting magnets in the 3d prints, shortening the drill bits…. Etc etc.
I have 6 of each size ready to go. I will list them tomorrow. I have more that still need final prep.
Thanks for your patience everyone.
IMG_0961.jpg
-
16th May 2024 11:54 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th May 2024, 10:18 AM #17
Thanks for your efforts would like to give it a go on some boxes I plan on making. Thanks for your efforts! [emoji120]
-
17th May 2024, 10:25 AM #18GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,071
Hi Paul,
i’d like to purchase a 1/4 inch kit and a 1/2 inch kit please.
Thanks,
Brian
-
17th May 2024, 04:03 PM #19Senior Member
- Join Date
- Mar 2014
- Location
- Cowes, Australia
- Posts
- 209
Thanks for the interest and encouragement. As always, it took 4x longer than I had anticipated. The next batch will be much prettier but also a bit more expensive.
So, I have listed them on the MARKETPLACE sub-forum. I have reserved kits for those who expressed interest and provided sizes. For those who didnt indicate which size they wanted please post a purchase request in the marketplace with your required size and I will ensure that you get one even if I run out of stock. I have no idea how these will sell but I promise that I will look after those in this sub-forum as I have stock left over.
Now, to clean up the colossal mess I left behind in the shop.
PS. I will post the dowel jig plan in the homemade tools/jig forum. I am working on making a cut list. I will be testing it next week or the week after (knee surgery next wednesday and not sure how I will recover) I have also ordered some PTFE plastic to act as the guide bushings which will ensure accuracy. They should arrive next week. This is the only non-plywood part of the jig other than the router and bit although I might be adding a cam device to dial in the dowel diameter. See this all on my post there.
Paul
-
19th May 2024, 11:49 PM #20Senior Member
- Join Date
- Mar 2014
- Location
- Cowes, Australia
- Posts
- 209
Ready for Aus post tomorrow morning.
PXL_20240519_124309126.jpg
-
21st May 2024, 02:00 PM #21
As mentioned earlier, I will take on of each when ready.
Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
Similar Threads
-
150mm Piano Hinge/ Continious Hinge
By tomartomau in forum BOX MAKINGReplies: 9Last Post: 19th November 2021, 10:03 AM -
Compound cupboard door hinge with pivot hinge mounting
By Gestalt in forum WOODWORK - GENERALReplies: 45Last Post: 28th August 2016, 08:45 PM -
Smart Hinge or Neat Hinge alternatives?
By Evanism in forum BOX MAKINGReplies: 3Last Post: 25th April 2015, 09:41 AM -
Wooden hinge
By Wooden Hinge in forum BOX MAKINGReplies: 0Last Post: 10th October 2012, 08:41 AM