Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 16
-
20th February 2013, 07:43 AM #1GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
How to resaw safely on the tablesaw?
The blade on my table saw projects 65mm above the table, and using a thin rip blade with 3mm kerf, I want to safely and neatly resaw 120mm boards on the table saw.
I tried it freehand, with a push stick and with a featherboard holding the material against the fence up to the start of the sawblade, and invariably the saw blade chewed into one side towards the end of the pass where I was unable to keep both pieces perfectly upright. I felt the situation was not under control and possibly dangerous and decided not to do it again until I knew how to do it properly.
Can anyone please suggest a proper method of doing this procedure by hand, if that is possible, or suggest some ideas for a jig that will do this safely and perfectly every time?regards,
Dengy
-
20th February 2013 07:43 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th February 2013, 09:26 AM #2
I have done it a million times. I will take some pictures tonight and show you how.
Visit my website at www.myFineWoodWork.com
-
20th February 2013, 11:13 AM #3
One option is to set the depth of cut just under half the board. Say, 58-59mm, so that you're leaving a thin connecting strip between the two boards.
The two halves can be quickly & easily separated with a handsaw or similar; I use a japanese pull-saw for this, as the lack of set to the teeth leaves minimal markings on the cut surfaces.
It does mean that the cut surfaces need to be dressed, but every oversized board I've ripped on a TS - no matter how I've ripped them - has needed a modicum of dressing anyway.
- Andy Mc
-
20th February 2013, 07:22 PM #4
What skew said plus you need 3 things.
1. a high fence to support the board
2. a push block to keep the board against the fence
3. a push stick
Use a bit of imagination you can cut veneers up to 1mm thick. No kidding.
P2200006.JPG
P2200007.JPG
P2200008.JPGVisit my website at www.myFineWoodWork.com
-
20th February 2013, 09:01 PM #5GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Many thanks for these photos Wongo, very much appreciated. Another case of a picture worth a 1,000 words
Can you please comfirm that you leave a small conmecting strip that has to be removed manually ? Even for your 1mm veneer? On a 1metre long board, surely that would take a bit of skill to get it right without damaging the freshly cut surfaces.
Would the use of a featherboard against your melamine horizontal pushboard improve the situation?
I like your big push block on topregards,
Dengy
-
20th February 2013, 10:58 PM #6
Can you please comfirm that you leave a small conmecting strip that has to be removed manually ?
Yes. Leaving a thin piece loose between the fence and the blade is not a good idea.
Even for your 1mm veneer? On a 1metre long board, surely that would take a bit of skill to get it right without damaging the freshly cut surfaces.
For 1mm veneer I use a different technique. Cut the veneer on the left side of the blade and do not leave a connecting strip. It is too hard to remove without damaging the surfaces. Move the fence by 4mm after each cut (4mm - 3mm blade width = 1mm veneer). You need to start with a fairly large block say 100mm wide. And you can only make 10-15 cuts before the block gets too small.
Would the use of a featherboard against your melamine horizontal pushboard improve the situation?
No. I hate featherboards. In my opinion they often make the situation awkward. Featherboards on a jointer or a router table is an absolute joke. I will shop here before the safety nazi jumping all over me.Visit my website at www.myFineWoodWork.com
-
21st February 2013, 05:28 PM #7SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Just a thought on using a thin kerf blade don't feed too fast as you run the risk of overloading,if that happens the blade will distort and you will not get an accurate cut.
-
22nd February 2013, 10:20 AM #8SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Nambour Qld
- Age
- 88
- Posts
- 688
-
22nd February 2013, 10:33 AM #9
-
26th February 2013, 01:23 PM #10SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Nambour Qld
- Age
- 88
- Posts
- 688
Hi Scott.
Is the question directed at me?
If so, then I call 3mm and 3.2mm(1/8") kerf standard kerf blades (what else?). I have a Flai Mustang 2.8 kerf and I don't call that thin.
My thin kerf blade is a CMT 1.7mm kerf.
If Dengue follows your advice he should overcome most of his resaw problems.Brian
-
26th February 2013, 01:30 PM #11
Thanks Brian. This is 1.7mm for a 25cm blade. I did not know they existed.
Visit my website at www.myFineWoodWork.com
-
26th February 2013, 01:37 PM #12
Now I must get one. What are the chances Carbatec actually have one in stock?
Visit my website at www.myFineWoodWork.com
-
26th February 2013, 04:11 PM #13Retired
- Join Date
- May 2012
- Location
- Canberra
- Posts
- 1,820
-
26th February 2013, 04:34 PM #14
Just read the fine print
Please note that thin kerf blades will require modified riving knives on most table saws to suitably match the thinner kerf of the blade.Visit my website at www.myFineWoodWork.com
-
26th February 2013, 06:11 PM #15SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Nambour Qld
- Age
- 88
- Posts
- 688
Every chance, Scott.
A blade this thin does not have very much carbide in the teeth and I reckoned mine would not take another sharpening so I bought a replacement from Carba-Tec only about a month ago.
As to the matter of thin riving knife, surely a bloke of your undoubted skill could make such a simple item.
My tablesaw came with a riving knife that came over the top of the blade, preventing partial cuts. Damned nuisance. I made two replacements from 1.5mm brass sheet using the bandsaw, drill and file. Nothing flash, but eminently serviceable.The thicker knife is two thicknesses epoxied together and sanded a little to reduce the thickness a tad.Brian
Similar Threads
-
Safely Weld a Car Tailgate?
By abrogard in forum WELDINGReplies: 38Last Post: 16th May 2011, 05:52 PM -
Take 2mm off - safely
By BeanerSA in forum WOODWORK - GENERALReplies: 4Last Post: 6th February 2011, 03:16 PM -
Can I safely use a 3/4" wide blade?
By didgemaker in forum BANDSAWSReplies: 11Last Post: 11th June 2010, 05:53 PM -
Turning Safely
By Ed Reiss in forum WOODTURNING - GENERALReplies: 6Last Post: 9th October 2008, 11:50 PM