Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 23
Thread: Sturdee Hold Downs
-
26th March 2004, 09:37 PM #1Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Sturdee Hold Downs
Following the introduction of the Sturdee range of shop aids with the Sturdee Knobs I am pleased to announce a new item being the Sturdee Hold Downs.
Similar to toggle clamps costing about $ 32 these wooden ones bcost about $ 2 for the hardware only as for the timber I use recycled ( not a greenie just cheap ) pine framing offcuts thrown out by a builder.
The inspiration for this hold down came from a photo in a woodworking book but carefull study showed that it needed three hands to operate ( and as I only have two ) I have made this improved version.
This pic shows the completed hold down in use.Last edited by Sturdee; 26th March 2004 at 09:58 PM.
-
26th March 2004 09:37 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
26th March 2004, 09:42 PM #2
You are constantly amazing I think we all look forward to any new 'post' by Sturdee .....its bound to be another little jig that is so useful.
What the red 'sawhandled' thing behind it you dont mind. Tonto
-
26th March 2004, 09:43 PM #3Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
The timber is all 19mm thick except the brace which is 3mm mdf.
For the handles you need 2 of 300*19mm and one of 100*40
The clamping arm is 255*50
The privot bracket requires two of 110*40,c rossbar of 55*40 and brace 95*50
For the base two of 100*100 and one of 100*45
This pic shows all the items needed includin hardware.
Peter
-
26th March 2004, 09:44 PM #4Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
This pic shows the pre assembly.
Peter.
-
26th March 2004, 09:46 PM #5Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
A pic showing , after painting the items assembled.
Peter
-
26th March 2004, 09:48 PM #6Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
And the other side.
Peter.
-
26th March 2004, 09:49 PM #7Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
The base unit attached to the bench.
Peter.
-
26th March 2004, 09:51 PM #8Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
The unit connected to the base.
Please not that the 6 inch adjusting bolt has a screw thread all the way , if not obtainable you can substitute it with threaded rod.
Peter.
-
26th March 2004, 09:53 PM #9Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Some more close ups.
Peter.
-
26th March 2004, 09:54 PM #10Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
And the final close up. Care must be taken with adjusting the screw clamp as neither too much or not enough pressure will stop the hold down to work. On the bottom of the screw are 3 nuts onto which is pushed the rubber chair stopper available from Clark's Rubber.
Peter.
-
26th March 2004, 09:57 PM #11Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
They don't take long to make. There is some fiddling needed with locating the position of the hinge but the longest part was the painting. I made four for use in the shop.
Peter.
-
26th March 2004, 10:07 PM #12Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Tony,
That red 'sawhandled' thing behind it is one of two right angled pushstick/clampdown I made to hold small pieces when using the mitre saw to stop them being picked up and thrown by the saw.
They are made for wide and narrow pieces and have sandpaper glued to the bottom to hold the small parts.
They work very well.
Peter.
-
26th March 2004, 10:29 PM #13
Great product placement in photo #7
-
26th March 2004, 10:36 PM #14
Hi Peter,
Some incredible stuff. I bet you get a lot of fun working out all these things. Keep it up you're an inspiration to all of us.
By the way where did you get the full threaded coach bolts from, have I been hanging around Bunnings too much.
-
26th March 2004, 11:11 PM #15Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Bazza,
I buy all my bolts and nuts from Cost Less Bolts in Ringwood. They are a specialist bolt supplier. If you buy from places like that in bulk the unit cost is a lot less than Bunnings. These particular bolts were 40 for $ 8.40 whereas Bunnings 6" bolts were 65 cents each.
Peter.