Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
1st August 2008, 08:47 AM #1
Deceased
- Join Date
- Jan 2006
- Location
- poland
- Age
- 78
- Posts
- 761
Table saw alignment & "short fence"
G'day Mates
I would like to share with you my method.
I think that almost all table saws comes from the factory "almost" aligned so, I'm using this procedure to "fine tune" the factory "almost"...
As you'll see, I'm not using any Hi-Tech nor Lo-Tech instruments because every blade has some run-out and flutter and I think that the blade itself "knows" the best if it's aligned or not.
I'm just "listening" what the blade it "telling" me and correcting accordingly...
The test must be done with the blade at "full up" position.
The "test piece" should be of MDF
Toooooo the pics.......
Regards
niki
-
1st August 2008 08:47 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
1st August 2008, 08:48 AM #2
Deceased
- Join Date
- Jan 2006
- Location
- poland
- Age
- 78
- Posts
- 761
-
3rd August 2008, 08:26 PM #3
Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Wow! Again!
G'day Niki, You are a bloody marvel.
Think I might have to getmy ears tuned first, however.
Last edited by artme; 15th June 2009 at 10:54 PM.
-
4th August 2008, 06:40 AM #4
Deceased
- Join Date
- Jan 2006
- Location
- poland
- Age
- 78
- Posts
- 761
Well, I don't know about you but....
Originally Posted by artme
Think I might have to getmy ears tuned first, however.
I had to deep clean my ears before I tuned the blade
Regards
niki
-
4th August 2008, 08:21 AM #5
Awaiting Email Confirmation
- Join Date
- Jan 2007
- Location
- Goulburn NSW
- Age
- 89
- Posts
- 913
Niki, you have done it again.
les
-
4th August 2008, 10:31 AM #6
GOLD MEMBER
- Join Date
- Oct 2007
- Location
- vic clayton
- Posts
- 1,041
nice one. obvious now that you point it out used to use my ears when tuning the triple su's on my old 240Z and have often heard the differences in sound that the blade makes as slowing down doh!!!
-
7th August 2008, 08:50 PM #7
Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Fubar! You Old Hoon!
Reply With QuoteSimilar Threads
-
"I see stupid people!" or "spot the blithering idiot"
By journeyman Mick in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 46Last Post: 29th October 2010, 07:29 AM -
"Folding adjustable height table" - small improvement
By niki in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 0Last Post: 1st July 2008, 07:05 AM -
Difference "Galvanised" and "Primed" Steel
By Fr_303 in forum METALWORK FORUMReplies: 4Last Post: 22nd January 2008, 05:59 PM -
"Brooklyn" 10" tablesaw with sliding table
By TassieKiwi in forum TABLE SAWS & COMBINATIONSReplies: 0Last Post: 10th March 2006, 11:04 AM
