Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Introducing me to inlays ...
-
22nd January 2009, 03:08 PM #1Golden Member
- Join Date
- Oct 2006
- Location
- Dandenong Ranges
- Age
- 47
- Posts
- 816
Introducing me to inlays ...
Hi folks,
I'm making a small side table (my first one) and I would like to create a square inlay (banding?) near the edge of the piece.
Could you point me to a few resources that might show/teach me how to do this? I've done a few searches are am not quite sure what the correct terminology is.
This is kind of the thing I'm after:
Thanks,
Af.___________________________________________________________
"The things I make may be for others, but how I make them is for me."
-
22nd January 2009 03:08 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
23rd January 2009, 08:54 PM #2
Hi Afro, There are a few good reference books around but for what you are after.
A quick crash course would be;
1. work out where you want the banding to go.
2.(Gently) cut the veneer into the required width strips, but a couple of inches longer than you need them.
3. Trim one end to the angle required, IF YOU MESS IT UP THAT'S WHERE THE EXTRA LENGTH IS HANDY!
4. Trim the opposite angle on the other end.
5. Glue and clamp (Sticky tape) together and leave to dry.
6. Lay out where you want it to go and tape it in place securely.
7. Cut around the outline of the banding (Carefully)
8. Remove base (Substraight) to the depth of the veneers thickness.
9. Glue into position with caulds or clamping boards for as long as the glue needs +24hrs,to make sure. I always use wax lunch wrap and newspaper to soak up extra glue and bleed out between the caulds.
10. Use a good sharp cabinet scraper the remove excess glue.
11. Sand block to desired smoothness I recommend 150~220~240~320~400, but whatever floats ya boat.
Word of caution when sanding be mindful of the main area around the banding not to rub to hard with in cross grain.
Let me know how it goes.
Cheers
SteveDiscover your Passion and Patience follows.
www.fineboxes.com.au
-
23rd January 2009, 09:13 PM #3Golden Member
- Join Date
- Oct 2006
- Location
- Dandenong Ranges
- Age
- 47
- Posts
- 816
Hi Steve,
Thanks so much for the response. This is why I love this forum so much. )
That's perfect and gives me a good guide to go on. I'll practice on some scraps and see how we go.
Thanks,
Af.___________________________________________________________
"The things I make may be for others, but how I make them is for me."
-
24th January 2009, 11:29 PM #4
Afro Boy,
I do a lot of this type of work. I use a plunge router to cut cut the rebate. First strip the veneer using a steel straight edge and trimming knife to the required width, a veneer saw is much better. Set the router to a depth to match the veneer banding. Use a bit a little smaller than the banding width and make two cuts to the exact width of the banding and trim the corners with a sharp chisel. I use a veneer hammer to lay the banding. Usually I do not have to press the banding, the glue as it sets will "draw" the banding into the recess, but the banding MUST be a firm fit.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
25th January 2009, 04:32 PM #5Golden Member
- Join Date
- Oct 2006
- Location
- Dandenong Ranges
- Age
- 47
- Posts
- 816
Thanks for the details Jim. I'm yet to get some time in the shop to try this out but hopefully some time this week.
Where do people usualy buy their veneer from? Any good suppliers in Melbourne or Australia?
Cheers,
Af.___________________________________________________________
"The things I make may be for others, but how I make them is for me."
-
25th January 2009, 09:15 PM #6SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 856
Afro Boy try:
Peter Scott-Young
37 Alexandra Rd, Ringwood East, VIC 3135
- Phone:(03) 9870 8733
- Fax:(03) 9870 8733
joez
-
28th January 2009, 12:29 PM #7Golden Member
- Join Date
- Oct 2006
- Location
- Dandenong Ranges
- Age
- 47
- Posts
- 816
Thanks for the recommendation. Unforunately Ringwood is a little far for me to get to easily. Any online options or are they far and few between here?
___________________________________________________________
"The things I make may be for others, but how I make them is for me."
-
28th January 2009, 02:03 PM #8SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 856
Similar Threads
-
half inlays swirls
By kruger in forum WOODTURNING - PEN TURNINGReplies: 15Last Post: 25th November 2008, 09:21 AM -
Marquetry inlays
By cellist in forum BOX MAKINGReplies: 2Last Post: 12th November 2008, 07:42 PM -
Inlays with CNC Machine
By rodm in forum MUSICAL INSTRUMENTSReplies: 0Last Post: 6th February 2008, 10:27 PM -
Epoxy inlays - advice please
By Jackson in forum WOODTURNING - GENERALReplies: 13Last Post: 24th October 2006, 11:33 AM -
Scrolling Inlays
By Old Bill in forum SCROLLERS FORUMReplies: 5Last Post: 16th April 2004, 03:29 AM