Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
14th January 2015, 10:31 PM #1Senior Member
- Join Date
- Feb 2013
- Location
- Laidley, SE Qld
- Posts
- 368
Need a 38 tooth change gear for Hafco AL340 lathe
My AL340 comes with change gears to cut a wide range of threads, but it can't cut 19TPI (1/4" & 3/8" BSP). Is someone on here who cuts gears able to cut a 38TPI gear for me? No rush, next time you are doing a batch of gears sort of thing.
I know you need more info than this, but to start the ball rolling, the 40 tooth change gear has a diameter of 42.2mm. I'd send one of the existing change gears, presumably the necessary cutter information etc can be derived from that. I doubt that the gears are made of anything exotic, and there is certainly no sign that the teeth have been heat treated.
I can supply the blank(s) if that helps.
PM me, or reply here, or email r-j-wardatbigponddotcom
-
14th January 2015 10:31 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th January 2015, 12:46 AM #2GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Let me know if you have no luck,no need to supply a sample but if you supply a blank I require a 9/16" or 5/8" reamed hole in the blank.
-
15th January 2015, 09:19 AM #3Novice
- Join Date
- Dec 2011
- Location
- England
- Posts
- 12
Sounds like MODULE 1.0. You should find that the OD of all of your gears are the tooth count + 2mm.
I did read somewhere else that the AL340 comes with MODULE 1.25 gears, which would make the OD of the 40 tooth gear 52.5mm, which definately doesn't sound right. MODULE 1 comes out at 42mm.
You might be able to find these off the shelf somewhere if you can alter the bore to suit.
Graham
-
15th January 2015, 09:58 AM #4GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
After reading the last post and checking this morning I only have M1.25 cutters so cant help,they must of changed the module size on the 340 somewhere down the track.
-
15th January 2015, 03:30 PM #5Senior Member
- Join Date
- Feb 2013
- Location
- Laidley, SE Qld
- Posts
- 368
40 tooth is 52.4mm
Mumble...lame excuse.....mumble. Apologies, a 40 tooth gear has an OD of 52.4mm. Thanks for the replies and interest.
Similar Threads
-
AL960b change gear tooth profile?
By variant22 in forum METALWORK FORUMReplies: 16Last Post: 22nd November 2014, 07:21 PM -
Help sought in identifying the make of lathe a change gear fits
By Tiptoeturtle in forum METALWORK FORUMReplies: 2Last Post: 11th December 2013, 11:22 AM -
Lathe thread cutting change gear calculator
By Vernonv in forum METALWORK FORUMReplies: 57Last Post: 4th December 2012, 12:23 PM -
30 tooth gear for Herless lathe needed
By Kentower in forum METALWORK FORUMReplies: 12Last Post: 23rd June 2011, 07:08 PM -
Gear tooth count on Back/Bull Gear.
By pipeclay in forum THE HERCUS AREAReplies: 31Last Post: 6th January 2010, 11:56 AM