Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
5th June 2015, 07:52 PM #1Novice
- Join Date
- Apr 2014
- Location
- Sunny Australia
- Posts
- 21
Aussie AL-960 owners or previous owners input please?
Hi, some time back I bought a well used AL-960 HAFCO lathe. (No, not an AL-960B)
It has been on the back burner for reasons I cant come up with but is now front and centre again.
Can anyone who has knowledge of them tell me what the T/R lever description or use is please?
I have tried in vain for a manual (HAFCO not being any help in that regard) but can only find either AL-960B which is a bit different or the 4003 Grizzly which again is similar but not the same.
Cheers, Peter (Wgong, NSW)
Pic at https://www.woodworkforums.com/album....hmentid=349161 $_58 (2).JPG
-
5th June 2015 07:52 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th June 2015, 08:00 PM #2GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Have you checked to see if it changes the direction of the lead/feed screw.
-
5th June 2015, 10:31 PM #3GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Townsville. Tropical Nth Qld.
- Posts
- 1,244
Is it T/R or L/R for left or right?
-
6th June 2015, 09:20 PM #4Novice
- Join Date
- Apr 2014
- Location
- Sunny Australia
- Posts
- 21
Yep, definitely T/R
You're on the money thanks pipeclay. It does change the direction. Im not sure how I missed that but......
So today I accidentally did a really neat job of machining up a piece of 3"od aluminium that I use as a drift and I was quite chuffed with myself.
While on a roll, I jumped into a steel drift but it looks pretty crap to the finish I got on the alloy drift.
Im off to investigate how the feed ratio works and hope that will help.
Thanks for the responses. Cheers, peterLast edited by befuddled; 6th June 2015 at 09:21 PM. Reason: spelling
-
6th June 2015, 10:14 PM #5GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Your finish will/could depend and quite a lot of variables.
Type of material,speed,tool type and geometry,rigidity of the lathe itself,and possibly the bearings in headstock,the length of the job,how the job is held ( 3 or 4 jaw chuck,whether supported by tailstock,depth of cut ) .
If you feel the feed rate is to high and can't reduce it further through the gearbox you can try putting a smaller gear on the stud position ( top) change gear,this will reduce your feed rate but you would need to do the calls to now what it is.
If you do change this gear make sure you put the correct one back on if screw cutting.
Similar Threads
-
To all Jet JPT 310 owners....
By Rob from Kew in forum TABLE SAWS & COMBINATIONSReplies: 12Last Post: 25th September 2012, 10:50 PM -
bp 355 owners
By R3R in forum BANDSAWSReplies: 18Last Post: 13th September 2009, 01:29 PM -
MK3 Owners - LOOK AT THIS
By Just George in forum TRITON / GMCReplies: 2Last Post: 1st June 2006, 12:50 PM -
To all JET 14” owners
By Wongo in forum BANDSAWSReplies: 3Last Post: 19th March 2006, 10:33 PM -
For KS-12K owners
By BobR in forum HAND TOOLS - POWEREDReplies: 8Last Post: 14th October 2004, 09:06 PM