Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 20 of 20
-
25th January 2012, 05:02 PM #16Dave J Guest
Hi Russell,
It was sort of a trial thing, but worked so good I left it on. The coolant doesn't go anywhere near the normal off on switch.
I have another switch to turn the coolant on or off when the saw is running. If the switch is on it will start the coolant with the motor and turn off when the motor does. It is located on the motor in the little electrical box, just a simple 240v rocker switch I had here.
Like I said in the other thread it's just a bit of rain water down pipe, and I tucked one leg up under the saw so it was held by the stand bolts, so no drilling any holes.
I found it does need the little thin tray on the rear as it drips off the blade and that catches it well and I get no coolant on the floor.
I tied the legs together with 2 pieces of angle and then used the tray as an extension off the down pipe. I also found this was needed because of the little splash and it some times runs along the job getting cut.
The way the tray is made allowed it to slot onto the edge of the down pipe and the other end I held up with a piece of wore onto the extended stop bar.
As I said above this was a trial and I do need to get around to making things permanent. I also need to raise my saw, but thats another job on the to do list, LOL
It is a bit cleaner at the moment, so if you need any more photos let me know.
Dave
-
25th January 2012 05:02 PM # ADSGoogle Adsense Advertisement
-
25th January 2012, 05:25 PM #17GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Hi Russell,
My pump is on while the motor is on, it just has a tap. I haven't cut much wood at all vertically.
Stuart
-
26th January 2012, 09:29 AM #18
Hi
I have just finished putting new guttering on the shed, so how fitting is it to have the left over piece of gutting fitted onto the saw.
My motor does not have a box on it so I will have to look at something a little different to yours for the switch.
I would use my saw as much in the vertical as horizontal so the switching off the coolant in the vertical might work well.
Russellvapourforge.com
-
26th January 2012, 01:22 PM #19Dave J Guest
Hi Russell,
Sounds like you gathering the materials quick.
On mine I used 100 x 75 mm down pipe (from memory) with the side cut out of it. The cut off side then made the end caps and other little drain at the end. But guttering should work as well.
I never did a step by step, so if you could post a few photos it may help others doing it in the future.
Dave
-
31st January 2012, 02:06 PM #20
Dave took your advice some what and reactivated your thread by putting a reply with my effort to now as it is about coolant for a saw.
https://www.woodworkforums.com/f65/ba...0/#post1438516
Russellvapourforge.com
Similar Threads
-
Bandsaw Blade
By m2c1Iw in forum BOAT RESOURCES / PRODUCT SEARCHReplies: 3Last Post: 1st September 2011, 12:03 AM -
bandsaw blade help
By garageman in forum HAND TOOLS - POWEREDReplies: 3Last Post: 21st June 2011, 07:39 PM -
Bandsaw blade
By dj_pnevans in forum BANDSAWSReplies: 1Last Post: 26th December 2009, 09:28 AM -
1/8th Bandsaw blade help
By Babylon5 in forum WOODWORK - GENERALReplies: 1Last Post: 18th November 2009, 05:07 AM -
looking for a new B/B suppler
By SPIRIT in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 10Last Post: 13th March 2008, 12:50 PM