Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: cutting a slot in aluminium
-
8th October 2010, 02:21 AM #1New Member
- Join Date
- Oct 2010
- Location
- england
- Posts
- 3
cutting a slot in aluminium
hello : ) i wonder if anyone can advise on which tool to use for my project? i need to cut a slot into a piece of sheet metal alu ( 1.25mm thick)
i've included a picture link below , the slot needs to be aprox 3.5mm wide x 16.5mm long
At the moment i think i may drill a series of holes and then file by hand with a needle file along them to make a slot, but it will be hard i feel to keep it straight?
thanks for any help : )
.
-
8th October 2010 02:21 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th October 2010, 09:35 AM #2GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
Do you have access to machine tools.
-
8th October 2010, 10:17 AM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
If you have access to a router it is relatively to make most of this cut in aluminium.
Firstly I would arrange to get the aluminium oversized and cut the slot first and then cut the aluminium to size around the slot - that way you get the slot exactly where you want it.
Then get a large piece of 12mm thick MDF and using big pieces of double sided tape stick the ally to the mdf.
Drill a starting and finishing hole in the metal/MDF slot big enough to accept the router tip.
Clamp the MDf to your bench and clamp a straight piece of wood to act as a fence along which to run the router
Rout the slot and finish the ends with file.
To help the router cut in Ally liberally coat the router tip with candle wax and rub wax along the area which is going to be cut.
Practice using a thin sheet of MDF.
I use routers and tables saws on Ally all the time. Take it slowly and use wax (or metho when the motor is some distance away) for a lubricant.
-
8th October 2010, 11:36 AM #4New Member
- Join Date
- Oct 2010
- Location
- england
- Posts
- 3
hello thanks for your replies . very kind of you.
i only have access to a mains electric hand held drill at present. a fine blade hack saw and other usual common tools. i was wondering if there was a tool i could buy? like a saw file or a punch type tool? or a special drill bit. sorry i did not say before.
thank you for you time.
-
8th October 2010, 11:59 AM #5GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Do you have files that will go in a 3.5mm slot?
If so, start by drilling a row of 2.5mm holes about 15mm long. File them to make a short slot. Us a vice or clamp a piece of wood/steel along the edge of the slot you want to support the sheet. Put a hacksaw blade through the slot you made(you may be able to use two blades on one saw if the cut they make is less than 3.5mm). Carefully cut down the middle of the slot. Clamp a piece of steel along one edge of the slot(a cheap steel rule if you have to). carefully file down to the rule. repeat on the other side of the slot.
Do you know what draw filing is?
Hope this helps you out.
Stuart
-
8th October 2010, 12:10 PM #6New Member
- Join Date
- Oct 2010
- Location
- england
- Posts
- 3
hi thanks
that's a great idea to clamp a steel ruler along the edge of the slot, i was really worried i would make a wobbly line. i have one of those in my tool box. Is draw filing is when you draw the file toward you in a stoking fashion?
thanks again for your help : )
-
8th October 2010, 12:44 PM #7SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Charlestown NSW
- Age
- 65
- Posts
- 899
Draw filing is when you hold the file in both hands (one hand on handle and the other the other end of the file) and have the long axis of the file at approx 90deg to the long axis of the job. File back and forth along the long axis of the job.
Instead of maybe wrecking your rule you could get 2 straight bits of angle and clamp the job between them in the vyce. this will give more support to your sheet and give you a straight edge to work to.n The very first thing to do on this job is mark it out so you can see where you are going with it.
bollie7
-
8th October 2010, 07:11 PM #8Senior Member
- Join Date
- Jul 2010
- Location
- Riverina NSW
- Posts
- 169
You could use an abro file, not to sure on the spelling
-
8th October 2010, 08:18 PM #9
If I were to do this I would clamp the aluminum to a piece of wood then clamp the lot to my table saw then slowly raise the blade to cut the slot. I am thinking off the top of my head that my blade is about 3.5mm thick.
Squirrel
-
9th October 2010, 09:13 PM #10SENIOR MEMBER
- Join Date
- Feb 2006
- Location
- Melbourne
- Age
- 65
- Posts
- 979
Hi Harps,
Firstly, what part of the Motherland are you from?
Secondly, what is it you are going to make from this training exercise?
Thirdly, looking at your drawing it appears that the slot is closer to one end of the strip than the other, yet there is only one dimension 15mm!!
I have a few ideas that will help if you can reply to my questions
Cheers
MH
-
9th October 2010, 09:27 PM #11Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 920
-
9th October 2010, 10:13 PM #12
When draw filling you use the file sideways.
For aluminium that's only 1.25mmm thick, you could even scratch your way through using a tungsten tipped laminate scoring tool.
For that sort of hole, I'd prefer a nibbling tool over a drill, though.
http://www.virtual-hideout.net/guide...de/index.shtml
Similar Threads
-
aluminium T-slot alternative
By Ch4iS in forum CNC MachinesReplies: 2Last Post: 31st May 2009, 08:30 PM -
Slot cutting help needed
By Lukesta in forum WOODWORK - GENERALReplies: 12Last Post: 11th March 2008, 12:19 AM -
Cutting 3-4mm aluminium on BS or TS
By old_picker in forum HAND TOOLS - POWEREDReplies: 7Last Post: 17th November 2006, 02:45 PM -
Cutting Aluminium box sections
By felixe in forum METALWORK FORUMReplies: 14Last Post: 29th May 2006, 12:30 AM -
T-slot aluminium extrusion
By Rocker in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 47Last Post: 29th May 2004, 09:53 PM