Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
20th December 2008, 07:59 AM #1
Vertical Storage of Metal Tube and Bar
At long last, I am sorting out the storage of longer metal stock in my workshop. I need to make a rack to store lengths of metal pipe and bar. Given my space limitation, I will need to store the lengths vertically and the method in the pictures below seems to be the way to go. I am interested to see whether there are any better solutions around. Is anyone using a better method than the one shown in the pictures?
The first step towards knowledge is to know that we are ignorant.
-
20th December 2008 07:59 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th December 2008, 11:14 AM #2
Looks good ,better than my system ,which is ,if there a space and it
fits then that will do .
I've got stuff all over the place ,but I know where to look.
Kev."Outside of a dog a book is man's best friend ,inside a dog it's too dark to read"
Groucho Marx
-
28th December 2008, 11:39 PM #3SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Perth
- Posts
- 649
Youve got the same problem as I used to have, the only issue with vertical storage is its no good for the smaller offcuts and they end up being left laying around everywhere or thrown away.
My setup is a horizontal set of mounts on the wall to stack 1200mm offcuts on top rack 800 offcuts on the second rack and 400mm offcuts on the bottom rack, all lengths 2000mm and above are vertically stacked in behind the rack as the rack is mounted 100mm of the wall.
Will dig up a photo for you
-
28th December 2008, 11:54 PM #4SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Perth
- Posts
- 649
Here she be
-
29th December 2008, 07:09 PM #5
Simso, thanks for the picture.
I am currently storing my shorter lengths of material in a variety of ways: smaller diameter rod in PVC under the lathe bench; aluminium, brass, steel and stainless offcuts in plastic bins; larger chunks of steel in pigeon holes; and sheet metal between cabinets. That said, the workshop is a bit of a mess although I did spend some of today tidying up, and also making more mess.
I like what you have done with the intermediate lengths. I will find a spot where I can store the mid-sized steel and aluminium horizontally and the longer stuff can go vertically.The first step towards knowledge is to know that we are ignorant.
-
31st December 2008, 02:17 AM #6GOLD MEMBER
- Join Date
- Oct 2003
- Location
- Sydney,Australia
- Posts
- 3,157
Just a thought - see if you can score some of those yellow/orange plastic rebar caps that they use all over construction sites - stick them over the ends of a few of the longer 'short' offcuts - they could save an eye if you bend down suddenly & don't see the odd bit sticking up.
Of course you may want some old time sabre fencing scars
-
2nd January 2009, 05:14 AM #7Home Hobbist
- Join Date
- Aug 2008
- Location
- Oatley NSW
- Age
- 69
- Posts
- 244
Hi Blu_Rock,
I have a good effective storage rack for my metal, its sheet steel folded then welded to shape. Attached is a picture of it.
Regards,
Keith.
-
2nd January 2009, 09:21 AM #8
Keith, nice solution and thanks for the picture.
bsrlee, I think I already have enough scars to last me a lifetime, although, a well-defined facial scar might give me an interesting pirate look.The first step towards knowledge is to know that we are ignorant.
Similar Threads
-
Metal Inlay Into Wood - Resin/Epoxy with metal powder?
By r5e in forum WOODWORK - GENERALReplies: 14Last Post: 15th March 2010, 11:17 AM -
Aluminium Metal tube
By brandon26 in forum METALWORK FORUMReplies: 2Last Post: 6th June 2006, 09:50 AM -
vertical
By Qldr in forum BANDSAWN BOXESReplies: 16Last Post: 3rd February 2005, 01:34 AM